K17 Electronic Brake Control Module (EBCM)

2012 Chevrolet Camaro LS, Standard TransSECTION K17 Electronic Brake Control Module (EBCM)
GM1862109Courtesy of
Connector Part Information
  • Harness Type: Forward Lamp
  • OEM Connector: 13518748
  • Service Connector: 19178089
  • Description: 38-Way F 2.8 Series, Sealed (BK)
Terminal Part Information
  • Pins: 1, 13, 25, 38
  • Terminated Lead: Pins: 1, 13, 38 - 13575408
  • Terminated Lead: Pin: 25 - 13575408
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-4A (PU)
  • Terminal/Tray: 15392777/23
  • Core/Insulation Crimp: D/5
  • Pins: 4, 6, 14, 15, 18-21, 24, 26, 27, 31-35, 37
  • Terminated Lead: Pins: 14, 15, 24, 26, 27, 35, 37 - 13578924
  • Terminated Lead: Pins: 4, 6, 18-21, 31-34 - 13578924
  • Release Tool: J-38125-215A
  • Diagnostic Test Probe: J-35616-64B (L-BU)
  • Terminal/Tray: SAITS-A03T-M064/14
  • Core/Insulation Crimp: 9/9
K17 Electronic Brake Control Module (EBCM)

Pin Wire Circuit Function
1 3 RD/BK 442 Battery Positive Voltage
2-4 - - Not Used
5 0.5 PU 333 Brake Fluid Level Sensor Signal
6 0.5 TN 833 Low Reference
7 - - Not Used
8 0.5 TN/WH 1384 Selective Ride Control Switch Signal (F55)
9 - 12 - - Not Used
13 3 BK 1050 Ground
14 0.35 TN 2501 High Speed GMLAN Serial Data Bus (-)
15 0.35 TN 2501 High Speed GMLAN Serial Data Bus (-)
16-17 - - Not Used
18 0.5 D-GN 872 Right Front Wheel Speed Sensor Signal
19 0.5 BN 882 Right Rear Wheel Speed Sensor Signal
20 0.5 OG 885 Low Reference
21 0.5 L-BU 830 Left Front Wheel Speed Sensor Signal
22-23 - - Not Used
24 0.35 L-BU 6106 High Speed GMLAN Serial Data (-)
25 2 RD/BK 1042 Battery Positive Voltage
26 0.35 TN/BK 2500 High Speed GMLAN Serial Data Bus (+)
27 0.35 TN/BK 2500 High Speed GMLAN Serial Data Bus (+)
28-30 - - Not Used
31 0.5 WH 883 Low Reference
32 0.5 D-GN 2087 12-Volt Reference
33 0.5 TN 884 Left Rear Wheel Speed Sensor Signal
34 0.5 YE 873 Low Reference
35 0.35 L-BU 5986 Serial Data Communication Enable
36 0.5 BN 7448 Vacuum Assist Pump Relay Coil Control
37 0.35 D-BU 6105 High Speed GMLAN Serial Data (+)
38 3 BK 1050 Ground
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.