Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2010RV CUTAWAY 6.6 LREPAIR AND DIAGNOSISQUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
2010 Chevrolet RV Cutaway 6.6 L
Specifications Index
2010 Chevrolet RV Cutaway 6.6 LSECTION Specifications Index
EXPRESS & SAVANA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 155 ft. lbs. (210 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LR-RF-LE. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Belt Routing | 4.3L See illustrations under DRIVE BELT REPLACEMENT
. 6.0L See illustrations under DRIVE BELT REPLACEMENT - ACCESSORY . 6.6L See illustrations under DRIVE BELT REPLACEMENT . |
||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 4.3L | ENGINE COOLANT THERMOSTAT REPLACEMENT (V6) | ||
| 6.0L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LLY,LBZ) | ||
| 6.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LGH) | ||
| Water Pump R & I | |||
| 4.3L | WATER PUMP REPLACEMENT (V6) | ||
| 4.8L & 5.3L | WATER PUMP REPLACEMENT (V8) | ||
| 6.0L | WATER PUMP REPLACEMENT (V8) | ||
| 6.6L | EXHAUST GAS RECIRCULATION COOLANT HOSES/PIPES REPLACEMENT (LMM) Or WATER PUMP OUTLET PIPE REPLACEMENT (LGH) | ||
| Engine Mechanical | |||
| 4.3L | |||
| Compression | No cylinder should read less than 100 psi (690 kPa) No cylinder should be less than 70 percent of the highest cylinder ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - at 1,000 RPM 6 psi (43 kPa) Oil Pressure - at 2,000 RPM 18 psi (125 kPa) Oil Pressure - at 4,000 RPM 24 psi (166 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 6.0L | |||
| Compression | No cylinder should read less than 100 psi (690 kPa) No cylinder should be less than 70 percent of the highest cylinder ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - at 1,000 RPM 6 psi (43 kPa) Oil Pressure - at 2,000 RPM 18 psi (125 kPa) Oil Pressure - at 4,000 RPM 24 psi (166 kPa) |
||
| Overhaul | See appropriate application ENGINE MECHANICAL SPECIFICATIONS (RPO L96 VIN G) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 6.6L | |||
| Compression | Minimum compression in any one cylinder is 2069 kPa (300 psi) There should not be more than 345 kPa (50 psi) difference from the average compression See ENGINE COMPRESSION TEST for LGH engine or see ENGINE COMPRESSION TEST for LMM engine. |
||
| Oil pressure | Minimum- Hot - at idle 14 psi (98 kPa) Minimum - 1800 RPM 42 psi (204 kPa) |
||
| Overhaul | See ENGINE MECHANICAL SPECIFICATIONS for LGH engine or ENGINE MECHANICAL SPECIFICATIONS for LMM engine. | ||
| Torque | See FASTENER TIGHTENING SPECIFICATIONS for LGH engine or FASTENER TIGHTENING SPECIFICATIONS for LMM engine. | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 4.3L | 74 ft. lbs. (100 N.m) | ||
| 6.0L | |||
| First Pass | 15 ft. lbs (20 N.m) | ||
| Second Pass | 37 ft. lbs. (50 N.m) | ||
| Final Pass | 74 ft. lbs (100 N.m) | ||
| 6.6L | |||
| First Pass | 58 ft. lbs. (79 N.m) | ||
| Second Pass | plus an additional 60 degrees | ||
| Final Pass | plus an additional 60 degrees | ||
| Fuel System | |||
| Pressure Specification | 4.3L 50-60 psi (345-414 kPa) 6.0L 50-60 psi (345-414 kPa) 6.6L See Test Procedure below |
||
| Fuel Pressure Test Procedure | 4.3L See FUEL SYSTEM DIAGNOSIS
. 6.0L See FUEL SYSTEM DIAGNOSIS (W/O FPCM) or FUEL SYSTEM DIAGNOSIS (W/FPCM) . 6.6L See FUEL SYSTEM DIAGNOSIS for LGH engine or FUEL SYSTEM DIAGNOSIS for LMM engine. |
||
| Fuel Filter Location | 4.3L The fuel filter is contained in the fuel sender/module assembly inside the fuel tank 6.0L The fuel filter is contained in the fuel sender/module assembly inside the fuel tank 6.6L There are 2 fuel filters, a cartridge style located in the diesel fuel conditioning module (DFCM) and a screw-on style fuel filter. See R & I below |
||
| Fuel Filter R & I | 4.3L See FUEL TANK FUEL PUMP MODULE REPLACEMENT 6.0L FUEL TANK FUEL PUMP MODULE REPLACEMENT 6.6L FUEL FILTER REPLACEMENT for LGH engine or FUEL FILTER REPLACEMENT For LMM engine. |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 4.3L 1,200-1,500 ohms per ft 6.0L 397-1,337 ohms 6.6L This application is a diesel engine not requiring spark plug wire |
||
| Ignition Wires (Routing) | |||
| 4.3L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| 6.0L | Spark plugs wires route directly down from coil to spark plug | ||
| 6.6L | This application is a diesel engine not requiring spark plug wires. | ||
| Spark Plug | |||
| 4.3L (Type GM P/N 12607234 or AC Delco P/N 41-993) | |||
| Gap | 0.060 in (1.5 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| 6.0L (Type GM P/N 12571164 or AC Spark Plug P/N 41-985) | |||
| Gap | 0.040 in (1.02 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| Starting | |||
| Starter | STARTING SYSTEM DESCRIPTION AND OPERATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque (See Tightening Pattern under wheel and tire INSTALLATION PROCEDURE | 140 ft. lbs. (190 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.