SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2010MALIBU LT, 3.6 7REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 948 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - E29RF THROUGH K33)COMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X5
2010 Chevrolet Malibu LT, 3.6 7

K9 Body Control Module X5

2010 Chevrolet Malibu LT, 3.6 7SECTION K9 Body Control Module X5
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: K9 Body Control Module X5 Connector End View
GM2282914Courtesy of GENERAL MOTORS CORP.
K9 Body Control Module X5

Pin Wire Circuit Function
1 0.35 YE/BK 1334 Left Rear Turn Signal Lamp Supply Voltage
0.35 YE/BK 1334 Left Rear Turn Signal Lamp Supply Voltage
2 0.35 L-BU/WH 1314 Left Front Turn Signal Lamp Supply Voltage
0.35 L-BU/WH 1314 Left Front Turn Signal Lamp Supply Voltage
3 3 RD/WH 3840 Battery Positive Voltage
4 3 RD/WH 3440 Battery Positive Voltage
5 0.35 OG 122 Rear Fog Lamp Supply Voltage (T79)
6 0.5 BN 5077 Low Reference
7 0.5 D-GN 7541 Stop Lamp Control Signal
8 0.35 OG 5186 Left Trailer Turn Signal Lamp Control
9 - - Not Used
10 0.35 D-GN/WH 1317 Fog Lamp Relay Control
11 0.35 L-GN 2270 Rear Window Washer Relay Control
12 0.35 L-BU/WH 6311 Brake Pedal Switch Signal
13 0.35 PK/WH 1970 Headlamp Low Beam Relay Control
14 0.35 L-GN 5486 Run Relay Coil Control
15 - - Not Used
16 0.35 L-GN/BK 3267 Child Security Lock Relay Control
17 0.35 YE 5187 Right Trailer Turn Signal Lamp Control
18 0.5 TN/WH 1969 Headlamp High Beam Relay Control
19 0.35 TN 28 Horn Relay Control
20 0.35 YE 5704 Liftgate Latch Relay Coil Control (Except TB5)
21 - - Not Used
22 0.35 D-BU 45 Park Lamp Supply Voltage/Marker Lamp Supply Voltage
23 - - Not Used
24 0.5 TN 860 Wiper Speed Relay Control
25 - - Not Used
26 0.5 WH 2282 Headlamp Washer Relay Control
Connector Part Information 
  • Harness Type: Body
  • OEM Connector: 13594130
  • Service Connector: 19151264
  • Description: 26-Way F 0.64 2.8 Series (BN)
Terminal Part Information 
  • Pins: 5-10, 12-14, 1-20, 22, 24, 26
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: 12094429/J-35616-64B (L-BU)
  • Pins: 1, 2
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: Pending
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
  • Pins: 3, 4
  • Terminal/Tray: SNAC-A081T-M2.8/20
  • Core/Insulation Crimp: A/D
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.