SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2010MALIBU LT, 3.6 7REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 948 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - E29RF THROUGH K33)COMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X2
2010 Chevrolet Malibu LT, 3.6 7

K9 Body Control Module X2

2010 Chevrolet Malibu LT, 3.6 7SECTION K9 Body Control Module X2
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: K9 Body Control Module X2 Connector End View
GM2282909Courtesy of GENERAL MOTORS CORP.
K9 Body Control Module X2

Pin Wire Circuit Function
1 2 RD/WH 2740 Battery Positive Voltage (except EXP)
0.8 RD/WH 2740 Battery Positive Voltage (EXP)
2 1 BK/WH 1751 Ground
3 0.8 RD/WH 2940 Battery Positive Voltage
4 3 RD/WH 4040 Battery Positive Voltage
5 0.35 GY 157 Courtesy Lamp Control
6 0.35 GY 5697 Child Security Indicator Control
7 0.35 YE 5361 Brake Pedal Position Sensor Signal
8 0.5 YE 6817 LED Backlight Dimming Control
9 - - Not Used
10 0.35 WH 278 Ambient Light Sensor Signal
11 0.35 PU 5526 Tap Up/Tap Down Switch Signal
12 0.35 GY 391 Rear Window Wiper Switch Signal
13 0.35 WH 5359 5-Volt Reference
14 0.35 L-BU 1788 Traction Control Switch Signal
15 0.35 OG/BK 781 Driver Door Lock Switch Unlock Signal
16 0.35 GY 3273 RCDLR Ground
17 0.35 L-GN/WH 5723 BCM Ignition Mode Data Signal
18 0.35 L-BU 3265 Child Security Lock Switch Signal
19 0.35 PK/BK 780 Driver Door Lock Switch Lock Signal
20 - - Not Used
21 0.35 GY 6135 Local Interconnect Network 4
22 0.35 D-GN 5060 Low Speed GMLAN Serial Data
23 0.35 TN 2501 High Speed GMLAN Serial Data Bus -
24 0.35 TN/BK 2500 High Speed GMLAN Serial Data Bus+
25 0.35 PK/WH 3272 RCDLR Power
26 0.35 WH 111 Hazard Switch Signal
27 0.35 L-BU/WH 3275 RCDLR Data Transmit
Connector Part Information 
  • Harness Type: Instrument Panel
  • OEM Connector: 13594133
  • Service Connector: 19151266
  • Description: 27-Way F 0.64 2.8 Series (L-BU)
Terminal Part Information 
  • Pins: 5-8, 10-27
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: 12094429/J-35616-64B (L-BU)
  • Pins: 1, 4
  • Terminal/Tray: SNAC-A081T-M2.8/20
  • Core/Insulation Crimp: A/D
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
  • Pins: 1-3
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: Pins 1, 3 - E/A
  • Core/Insulation Crimp: Pins 2 - C/A
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.