SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2010MALIBU LT, 3.6 7REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 948 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - E29RF THROUGH K33)COMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X1
2010 Chevrolet Malibu LT, 3.6 7

K9 Body Control Module X1

2010 Chevrolet Malibu LT, 3.6 7SECTION K9 Body Control Module X1
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: K9 Body Control Module X1 Connector End View
GM2282907Courtesy of GENERAL MOTORS CORP.
K9 Body Control Module X1

Pin Wire Circuit Function
1 1 BK/WH 1751 Ground
2 0.8 RD/WH 2540 Battery Positive Voltage (EXP)
3 RD/WH 2540 Battery Positive Voltage (except EXP)
3 0.5 RD/WH 2140 Battery Positive Voltage
4 0.5 RD/WH 2240 Battery Positive Voltage
5 0.35 PU/WH 6816 LED Dimming Signal
6 0.35 YE 7554 Shift Control Signal
7 - - Not Used
8 0.35 L-GN 5720 ACC Indicator Control
9 0.35 D-GN 7555 Headlamp Switch Signal
10 - - Not Used
11 0.35 D-GN 306 Headlamp Switch Headlamps Off Signal/Automatic Headlamp Low Control
12-13 - - Not Used
14 0.35 PU 328 Interior lamp Defeat Switch Signal
15 - - Not Used
16 0.35 WH 103 Headlamp Switch Headlamps On Signal
17 - - Not Used
18 0.35 D-BU 5904 Column Lock Status (ULS)
19 0.35 BN 5360 Low Reference
20 0.35 D-BU 5719 Start Indicator Control
21 0.35 GY 728 Security Indicator Control
22 0.35 L-BU 13 Headlamp Switch Park Lamps Signal
23 0.35 PU 7558 Accent Lamps Control (EXP)
24 0.35 TN 2501 High Speed GMLAN Serial Data Bus -
25 0.35 TN/BK 2500 High Speed GMLAN Serial Data Bus+
26 0.35 L-GN 3274 RCDLR Data Receive
Connector Part Information 
  • Harness Type: Instrument Panel
  • OEM Connector: 13594128
  • Service Connector: 19151262
  • Description: 26-Way F 0.64 2.8 Series (WH)
Terminal Part Information 
  • Pins: 5, 6, 8, 9, 11, 14, 16, 18-26
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: 12094429/J-35616-64B (L-BU)
  • Pins: 2
  • Terminal/Tray: SNAC-A081T-M2.8/20
  • Core/Insulation Crimp: A/D
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
  • Pins: 1-4
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: Pins 1 - C/A
  • Core/Insulation Crimp: Pins 2, 3, 4 - E/A
  • Release Tool/Test Probe: 12094429/J-35616-35 (VT)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.