K17 Electronic Brake Control Module

2010 Chevrolet Malibu LT, 3.6 7SECTION K17 Electronic Brake Control Module
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: K17 Electronic Brake Control Module Connector End View
GM1830966Courtesy of GENERAL MOTORS CORP.
K17 Electronic Brake Control Module

Pin Wire Circuit Function
1 5 RD/BK 442 Battery Positive Voltage
2 - - Not Used
3 0.5 L-GN 1903 Vehicle Speed Signal
4-7 - - Not Used
8 0.5 L-BU 5986 Serial Data Communication Enable
9-10 - - Not Used
11 0.35 TN/BK 2500 High Speed GMLAN Serial Data Bus+
12 0.5 TN/BK 2500 High Speed GMLAN Serial Data Bus+
13 0.5 TN 2501 High Speed GMLAN Serial Data Bus -
14 0.35 TN 2501 High Speed GMLAN Serial Data Bus -
15 0.5 YE 6641 Variable Effort Steering Solenoid Low Control
16 5 BK 1050 Ground
17 0.5 D-BU 6105 High Speed GMLAN Serial Data (+)
18-19 - - Not Used
20 0.5 L-BU 6106 High Speed GMLAN Serial Data (-)
21 - - Not Used
22 0.5 D-GN 2087 12-Volt Reference
23-25 - - Not Used
26 0.5 GY 6031 5-Volt Reference
27 0.5 YE/BK 6032 Low Reference
28-31 - - Not Used
32 2 RD/BK 1042 Battery Positive Voltage
33 0.5 TN 833 Right Front Wheel Speed Sensor Low Reference
34 0.5 D-GN 872 Right Front Wheel Speed Sensor Signal
35 0.5 BN 6305 Vacuum Pump Relay Control
36 0.5 TN 884 Left Rear Wheel Speed Sensor Signal
37 0.5 OG 885 Left Rear Wheel Speed Sensor Low Reference
38 - - Not Used
39 0.5 PU 333 Brake Fluid Level Sensor Signal
40 - - Not Used
41 0.5 OG 6030 Brake Booster Vacuum Sensor Signal
42 0.5 WH 883 Right Rear Wheel Speed Sensor Low Reference
43 0.5 BN 882 Right Rear Wheel Speed Sensor Signal
44 0.5 BN 1295 Variable Effort Steering Solenoid High Control
45 0.5 L-BU 830 Left Front Wheel Speed Sensor Signal
46 0.5 YE 873 Left Front Wheel Speed Sensor Low Reference
47 - - Not Used
Connector Part Information 
  • Harness Type: Body
  • OEM Connector: 13547678
  • Service Connector: 19115598
  • Description: 47-Way F MK25 Series (BK)
Terminal Part Information 
  • Pins: 1, 16, 32
  • Terminal/Tray: 7116-4142-02/10
  • Core/Insulation Crimp: Pins 1, 16 - D/3
  • Core/Insulation Crimp: Pins 32 - Pending
  • Release Tool/Test Probe: 12094430/J-35616-42 (RD)
  • Pins: 3, 8, 11-14, 15, 17, 20, 22, 26, 27, 33-37, 39, 41-46
  • Terminal/Tray: 638551-1/16
  • Core/Insulation Crimp: Pins 3, 8, 12, 13, 15, 17, 20, 22, 26, 27, 33-37, 39, 41-46 - K/K
  • Core/Insulation Crimp: Pins 11, 14 - J/J
  • Release Tool/Test Probe: 15315247/J-35616-64B (L-BU)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.