Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Rear Differential Clutch Control Module Scan Tool Information
2010 Chevrolet Malibu LT, 3.6 7SECTION Rear Differential Clutch Control Module Scan Tool Information
WARNING: This page is about a different car, the 2010 Cadillac SRX. However, it is still accessible from the selected car via links, so may be relevant.
Rear Differential Clutch Control Module Scan Tool Data Parameters
| Parameter | Expected Value | Description |
|---|---|---|
| Operating Conditions: Ignition is ON, engine OFF, and vehicle is stationary | ||
| Left Front Wheel Speed Sensor | 0 | The scan tool displays 0-160 km/h (0-99.5 MPH). The scan tool displays 0 km/h (0 MPH) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 MPH). |
| Left Rear Wheel Speed Sensor | 0 | The scan tool displays 0-160 km/h (0-99.5 MPH). The scan tool displays 0 km/h (0 MPH) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 MPH). |
| Rear Differential Clutch Control Module Temperature | Varies | The scan tool displays °C. The scan tool indicates a range from -40 to 215 °C. |
| Rear Differential Clutch Pump Motor Current | 0 | The scan tool displays the current in mA through the pump motor. |
| Rear Differential Clutch Solenoid Valve Current | 0 | The scan tool displays the current in mA through the rear differential clutch solenoid valve. |
| Rear Differential Clutch Status | Temporarily Disabled | The scan tool displays either Normal, Temporarily Disabled, Temporarily Limited, Malfunctioned, or Externally Disabled. |
| Rear Drive Clutch Solenoid Valve Current | 0 | The scan tool displays the current in mA through the rear drive clutch solenoid valve. |
| Rear Drive Clutch Status | Temporarily Disabled | The scan tool displays either Normal, Temporarily Disabled, Temporarily Limited, Malfunctioned, or Externally Disabled. |
| Right Front Wheel Speed Sensor | 0 | The scan tool displays 0-160 km/h (0-99.5 MPH). The scan tool displays 0 km/h (0 MPH) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 MPH). |
| Right Rear Wheel Speed Sensor | 0 | The scan tool displays 0-160 km/h (0-99.5 MPH). The scan tool displays 0 km/h (0 MPH) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 MPH). |
Rear Differential Clutch Control Module Scan Tool Output Controls
| Output Control | Description |
|---|---|
| Pump Motor | This function allows the technician to command the pump motor ON and OFF. |
| Rear Differential Clutch Solenoid Valve | This function allows the technician to command the clutch solenoid valve. The system will increase or decrease the current in increments of 200 mA |
| Rear Drive Clutch Solenoid Valve | This function allows the technician to command the clutch solenoid valve. The system will increase or decrease the current in increments of 200 mA |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.