Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2009TAHOE BASE, 4.8 CREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 47 (DISC BRAKE SYSTEM)REPAIR INSTRUCTIONSREAR BRAKE ROTOR REPLACEMENT (2500 SERIES)INSTALLATION PROCEDURE
2009 Chevrolet Tahoe Base, 4.8 C
Installation Procedure
2009 Chevrolet Tahoe Base, 4.8 CSECTION Installation Procedure
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
- Use the J 42450-A to clean all rust and contaminants from the mating surface of the hub flange. See Special Tools .
- Use the J 41013 to clean all rust and contaminants from the inside diameter of the hat section of the brake rotor to prevent any foreign material from getting between the brake rotor and the hub flange. See Special Tools .
- Inspect the mating surfaces of the hub/axle flange and the rotor to ensure that there are no foreign particles or debris remaining.
- Align the rotor to its original position on the hub, if applicable.
- Install the rotor by slowly turning the rotor while pushing the rotor towards the axle.
- If the rotor was removed and installed as part of a brake system repair, measure the assembled lateral runout (LRO) of the rotor to ensure optimum performance of the disc brakes. Refer to Brake Rotor Assembled Lateral Runout Measurement .
- If the rotor assembled LRO measurement exceeds the specification, bring the LRO to within specifications. Refer to Brake Rotor Assembled Lateral Runout Correction .
- Install the caliper and caliper bracket as an assembly.
- Perform the following procedure before installing the brake caliper bracket bolts.
- Remove all traces of the original adhesive patch.
- Clean the threads of the bolts with brake parts cleaner or the equivalent and allow to dry.
- Apply threadlocker GM P/N 12345493 (Canadian P/N 10953488) to the threads of the bolts.
- Install the brake caliper bracket bolts.
Tighten: Tighten the bolts to 200 N.m (148 lb ft).
- Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation .
- Lower the vehicle.
- With the engine OFF gradually apply the brake pedal to approximately 2/3 of its travel distance.
- Slowly release the brake pedal.
- Wait 15 seconds then repeat steps 13-14 until a firm pedal is obtained. This will properly seat the caliper pistons and pads.
- Fill the master cylinder reservoir to the proper level with clean brake fluid, if necessary. Refer to Master Cylinder Reservoir Filling .
IMPORTANT:
Whenever the brake rotor has been separated from the hub/axle flange, any rust or contaminants should be cleaned from the hub/axle flange and the brake rotor mating surfaces. Failure to do this may result in excessive assembled lateral runout (LRO) of the brake rotor, which could lead to brake pulsation.
NOTE:
Refer to Fastener Notice
.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.