Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2009TAHOE BASE, 4.8 CREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 422 (FRONT SUSPENSION SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2009 Chevrolet Tahoe Base, 4.8 C
Fastener Tightening Specifications
2009 Chevrolet Tahoe Base, 4.8 CSECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Brake Hose Bracket Bolt | 9 N.m | 80 lb in |
| Brake Hose Clip Bolts | 12 N.m | 106 lb in |
| Hub and Bearing Assembly to Steering Knuckle Bolts | 180 N.m | 133 lb ft |
| Lower Ball Joint Stud Nut | ||
| First Pass | 50 N.m | 37 lb ft |
| Final Pass | plus 95 degrees | |
| Lower Control Arm to Frame Nuts | 175 N.m | 129 lb ft |
| Shock Absorber Electrical Connector | 20 N.m | 15 lb ft |
| Shock Absorber Module to Frame Nuts - 1500 Series | 50 N.m | 37 lb ft |
| Shock Absorber Module to Lower Control Arm Bolt - 1500 Series | 50 N.m | 37 lb ft |
| Shock Absorber Module to Lower Control Arm Nut - 2500 Series | 80 N.m | 59 lb ft |
| Shock Absorber Tenon Nut - 1500 Series (w/Electrical Suspension) | 80 N.m | 59 lb ft |
| Shock Absorber Tenon Nut - 1500 Series (w/o Electrical Suspension) | 50 N.m | 37 lb ft |
| Shock Absorber Tenon Nut - 2500 Series | 23 N.m | 17 lb ft |
| Spring Jounce Bumper Nut - 2500 Series | 30 N.m | 22 lb ft |
| Stabilizer Shaft Insulator Clamp Bolts | 50 N.m | 37 lb ft |
| Stabilizer Shaft Link Nuts | 23 N.m | 17 lb ft |
| Suspension Position Sensor Bolt | 12 N.m | 106 lb in |
| Torsion Bar Support Link Bolt/Screw | 95 N.m | 70 lb ft |
| Upper Ball Joint Stud Nut | 50 N.m | 37 lb ft |
| Upper Control Arm to Frame Nuts | 190 N.m | 140 lb ft |
| Wheel Speed Sensor Mounting Bolt | 18 N.m | 13 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.