SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2009TAHOE BASE, 4.8 CREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 411 (COMPONENT LOCATIONS - ELECTRICAL CENTER IDENTIFICATION VIEWS)ELECTRICAL CENTER IDENTIFICATION VIEWSFUSE BLOCK - I/P X4
2009 Chevrolet Tahoe Base, 4.8 C

Fuse Block - I/P X4

2009 Chevrolet Tahoe Base, 4.8 CSECTION Fuse Block - I/P X4
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Fuse Block - I/P X4 Connector End Views
GM1667402Courtesy of GENERAL MOTORS CORP.
Fuse Block - I/P X4

Pin Wire Circuit Function
A1 2 RD/WH 1240 Battery Positive Voltage
A2 0.35 D-GN 5060 Low Speed GMLAN Serial Data
A3-A4 - - Not Used
A5 0.35 PK 1691 Low Reference (DL3 or DR4)
A6-A7 - - Not Used
B1 3 BK 1850 Ground
B2 0.5 L-BU/WH 1314 Left Front Turn Signal Lamp Supply Voltage (DL3 or DPN)
B3 0.5 D-GN 5060 Low Speed GMLAN Serial Data
B4 0.8 RD/WH 140 Battery Positive Voltage
B5 0.5 GY 118 Left Front Speaker Output (-) (UQ3)
0.8 GY 118 Left Front Speaker Output (-) (UQA/UQS)
B6 0.5 TN 201 Left Front Speaker Output (+) (UQ3)
0.8 TN 201 Left Front Speaker Output (+) (UQA/UQS)
B7 0.35 GY 1690 Automatic Day/Night Mirror Signal (DL3 or DR4)
Connector Part Information
  • Harness Type: Driver Door
  • OEM Connector: 15467622
  • Service Connector: 19115664
  • Description: 14-Way F GT 150 280 Series (L-GY)

Terminal Part Information
  • Pins: A1, B1
  • Terminated Lead: Pins A1 - 13575754
  • Terminated Lead: Pins B1 - 13575756
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-4A (PU)
  • Terminal/Tray: 15304713/19
  • Core/Insulation Crimp: Pins A1 - 4/4
  • Core/Insulation Crimp: Pins B1 - F/D
  • Pins: A2, A5, B2, B5, B6
  • Terminated Lead: 13575735
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-2A (GY)
  • Terminal/Tray: 12191812/19
  • Core/Insulation Crimp: Pins A2, B2, B5 (UQ3), B6 (UQ3) - E/C
  • Core/Insulation Crimp: Pins B5 (UQA or UQS), B6 (UQA or UQS) - C/A
  • Pins: B4, B7
  • Terminated Lead: 13575753
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-4A (PU)
  • Terminal/Tray: 15304711/8
  • Core/Insulation Crimp: Pins B4 - 2/A
  • Core/Insulation Crimp: Pins B7 - E/A
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.