Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSCHEVROLET2008HHR SS, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSWIRING DIAGRAMSWIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT VIEWS & COMPONENT CONNECTOR END VIEWSCOMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM) X1
2008 Chevrolet HHR SS, Standard
Body Control Module (BCM) X1
2008 Chevrolet HHR SS, StandardSECTION Body Control Module (BCM) X1
Body Control Module (BCM) X1
| Pin | Wire | Circuit | Function |
|---|---|---|---|
| 1 | 0.35 L-BU/BK | 747 | Left Rear Door Ajar Switch Signal |
| 2 | - | - | Not Used |
| 3 | 0.35 PU | 5531 | Hood Closed Switch Signal (AP3) |
| 4 | 0.35 PK/BK | 109 | Hood Ajar Switch Signal (AP3) |
| 5 | 0.35 TN | 755 | Sunroof Enable Signal (CF5) |
| 6 | 0.35 WH | 682 | Door Lock Lock/Unlock Signal |
| 7 | 0.35 WH/BK | 682 | Door Lock Lock/Unlock Signal |
| 8 | 0.35 WH/RD | 1080 | Park Lamp Relay Control |
| 9 | 0.35 YE | 5456 | Rear Wiper Park Signal |
| 10-12 | - | - | Not Used |
| 13 | 0.35 PK | 849 | Brake Fluid Level Sensor Signal |
| 14 | 0.35 L-BU | 1134 | Park Brake Switch Signal |
| 15 | 0.35 YE | 5199 | Run/Crank Relay Coil Control |
| 16 | 0.35 WH | 193 | Rear Defog Relay Control |
| 17 | 0.35 D-BU | 15 | Right Turn Signal Lamp Supply Voltage |
| 18 | 0.35 D-GN | 5060 | Low Speed GMLAN Serial Data (U2K) |
| 19 | 0.35 TN/WH | 746 | Right Front Door Ajar Switch Signal |
| 20 | 0.35 L-GN/BK | 748 | Right Rear Door Ajar Switch Signal |
| 21 | - | - | Not Used |
| 22 | 0.35 GY/BK | 745 | Left Front Door Ajar Switch Signal |
| 23-30 | - | - | Not Used |
| 31 | 0.35 L-BU | 1344 | Liftgate Release Relay Control |
| 32 | - | - | Not Used |
| 33 | 0.35 D-GN/WH | 1135 | A/T Shift Interlock Solenoid Supply Voltage (MN5) |
| 34 | - | - | Not Used |
| 35 | 0.35 L-BU | 14 | Left Turn Signal Lamp Supply Voltage |
| 36 | 0.35 D-GN | 5060 | Low Speed GMLAN Serial Data (UE1) |
| 37-39 | - | - | Not Used |
| 40 | 0.35 L-BU | 1788 | Traction Control Switch Signal (JL4/JL9) |
| 41-43 | - | - | Not Used |
| 44 | 0.35 TN/WH | 1969 | Headlamp High Beam Relay Control |
| 45-46 | - | - | Not Used |
| 47 | 0.35 YE | 196 | Windshield Wiper Motor Park Switch Signal |
| 48-50 | - | - | Not Used |
| 51 | 0.35 D-GN | 113 | Windshield Wiper Switch Signal 2 |
| 52-53 | - | - | Not Used |
| 54 | 0.35 YE | 317 | Fog Lamp Relay Control (T37) |
| 55 | 0.35 PK/BK | 1303 | Liftgate Ajar Switch Signal |
| 56-57 | - | - | Not Used |
| 58 | 0.35 L-GN | 2270 | Rear Window Washer Relay Control |
| 59 | 0.35 GY | 391 | Rear Window Wiper Switch Signal |
| 60 | 0.35 TN | 28 | Horn Relay Control |
| 61 | 0.35 BK/WH | 1251 | Signal Ground |
| 62 | 0.35 RD/WH | 1340 | Battery Positive Voltage |
| 63 | 0.35 GY | 596 | 5-Volt Reference |
| 64 | 0.35 BK/WH | 851 | Signal Ground |
| 65 | 0.35 TN/WH | 1704 | Sensor Low Reference |
| 66 | - | - | Not Used |
| 67 | 0.35 YE | 61 | Low Reference |
| 68 | 0.35 WH | 5075 | Current Sensor Signal |
| 69 | 0.35 WH/BK | 1221 | Liftgate Release Switch Signal (-Panel Van) |
| 0.35 L-GN | 5926 | Release Switch Signal (Panel Van) | |
| 70 | 0.35 D-GN/WH | 636 | Ambient Air Temperature Sensor Signal |
| 71 | 0.35 L-GN/BK | 592 | DRL Relay Control |
| 72 | - | - | Not Used |
Connector Part InformationÂ
|
Terminal Part InformationÂ
|
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.