Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G3500, VAN PASSENGER EXTENDEDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 131 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT VIEWS & COMPONENT CONNECTOR END VIEWS)ELECTRICAL CENTER IDENTIFICATION VIEWSBODY CONTROL MODULE (BCM) X2
2008 Chevrolet Chevy Express G3500, Van Passenger Extended
Body Control Module (BCM) X2
2008 Chevrolet Chevy Express G3500, Van Passenger ExtendedSECTION Body Control Module (BCM) X2
WARNING: This page is about a different car, the 2008 Chevrolet Malibu Classic. However, it is still accessible from the selected car via links, so may be relevant.
Body Control Module (BCM) X2
| Pin | Wire | Circuit | Function |
|---|---|---|---|
| 1 | 0.35 TN/BK | 2500 | High Speed GMLAN Serial Data Bus + |
| 2 | 0.35 TN/BK | 2500 | High Speed GMLAN Serial Data Bus + |
| 3 | 0.35 PK/WH | 1970 | Headlamp Low Beam Relay Control |
| 4 | 0.35 PU | 524 | Headlamp Dimmer Switch High Beam Signal |
| 5 | 0.35 BN/WH | 301 | Park Lamp Switch Signal |
| 6 | 0.35 L-GN | 696 | Cruise Control Cancel Signal |
| 7-8 | - | - | Not Used |
| 9 | 0.35 WH | 111 | Hazard Switch Signal |
| 10 | - | - | Not Used |
| 11 | 0.35 D-GN | 264 | Security Indicator Signal |
| 12 | 0.35 L-GN | 377 | Serial Data |
| 13 | 0.8 BK/WH | 651 | Ground |
| 14 | 0.35 TN | 28 | Horn Relay Control |
| 15 | 0.35 WH | 103 | Headlamp Switch Headlamps On Signal |
| 16 | 0.35 OG | 192 | Front Fog Lamp Switch Signal (T96) |
| 17 | 0.35 PU/WH | 549 | Headlamp Switch Headlamps Off Signal |
| 18 | 0.35 WH | 5359 | 5-Volt Reference |
| 19 | 0.35 TN | 2501 | High Speed GMLAN Serial Data Bus - |
| 20 | 0.35 TN | 2501 | High Speed GMLAN Serial Data Bus - |
| 21-25 | - | - | Not Used |
| 26 | 0.35 D-GN | 44 | Instrument Panel Lamps Dimmer Switch Signal |
| 27-28 | - | - | Not Used |
| 29 | 0.35 L-GN | 5980 | Adjustable Pedal Inhibit Signal (JF4) |
| 30 | - | - | Not Used |
| 31 | 0.35 YE | 5361 | Brake Pedal Position Sensor Signal |
| 32 | - | - | Not Used |
| 33 | 0.35 YE | 317 | Fog Lamp Relay Control (T96) |
| 34-36 | - | - | Not Used |
| 37 | 0.35 D-GN | 5060 | Low Speed GMLAN Serial Data |
| 38 | 0.35 D-GN | 5060 | Low Speed GMLAN Serial Data |
| 39-43 | - | - | Not Used |
| 44 | 0.35 L-GN/BK | 1137 | DRL Ambient Light Sensor Signal |
| 45-46 | - | - | Not Used |
| 47 | 0.35 YE/BK | 1138 | DRL Ambient Light Sensor Low Reference |
| 48-50 | - | - | Not Used |
| 51 | 0.35 BN | 1356 | Flash To Pass Switch Signal |
| 52-54 | - | - | Not Used |
| 55 | 0.35 D-GN | 5060 | Low Speed GMLAN Serial Data |
| 56 | 0.35 WH | 1390 | Off/Run/Crank Voltage |
| 57 | 0.35 GY | 112 | Windshield Wiper Switch Signal 1 |
| 58 | 0.35 PU | 719 | Low Reference |
| 59 | 0.35 BN | 5360 | Low Reference |
| 60 | - | - | Not Used |
| 61 | 0.35 GY | 1884 | Cruise Control Switch Signal |
| 62 | 0.35 WH/BK | 1073 | 5-Volt Reference |
| 63-65 | - | - | Not Used |
| 66 | 0.35 YE/BK | 1418 | Left Rear Turn Signal Switch Signal |
| 67 | 0.35 D-GN/WH | 1419 | Right Rear Turn Signal Switch Signal |
| 68 | 0.35 L-BU | 292 | Rear Defog Switch Signal (C60) |
| 69 | 0.35 D-GN/WH | 762 | A/C Request Signal (C60) |
| 70 | - | - | Not Used |
| 71 | 0.35 PU | 5234 | Passenger Seat Belt Indicator Control |
| 72 | 0.35 TN | 683 | Rear Defog Relay Control (C60) |
Connector Part Information
|
Terminal Part Information
|
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.