SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 365 (CRUISE CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC P0567 (6.6L): CRUISE CONTROL RESUME SWITCH CIRCUITTEST DESCRIPTION
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6

Test Description

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Test Description
WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step determines if condition is present.
DTC P0567 (6.6L)

Step Action Yes No
Schematic Reference : Cruise Control Schematics 
Connector End View Reference: Cruise Control Connector End Views  or Engine Control Module (ECM) Connector End Views in Engine Controls - 6.6L (LB7) or to Engine Control Module (ECM) Connector End Views in Engine Controls - 6.6L (LLY)
1 Did you perform the Cruise Control Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Cruise Control 
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Turn the cruise On/Off control switch ON.
  4. With the scan tool, observe the Cruise Resume/Accel. Switch parameter in the PCM data list.
Does the Cruise Resume/Accel. Switch parameter display On?		 Go to Step 3  Go to Diagnostic Aids
3
  1. Turn OFF the ignition.
  2. Disconnect the cruise control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Cruise Resume/Accel. Switch parameter in the PCM data list.
Does the Cruise Resume/Accel. Switch parameter display On?		 Go to Step 4  Go to Step 5 
4 Test the cruise control resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 6 
5 Inspect for poor connections at the harness connector of the cruise control switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 7 
6 Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 8 
7 Replace the cruise control switch. Refer to Multifunction, Turn Signal Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 9  -
8
IMPORTANT: Program the replacement ECM.
Replace the ECM. Refer to Engine Control Module (ECM) Replacement in Engine Controls - 6.6L (LB7) or to Engine Control Module (ECM) Replacement in Engine Controls - 6.6L (LLY).Did you complete the replacement?		 Go to Step 9  -
9
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.
Does the DTC reset?		 Go to Step 2  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.