Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2313 (VEHICLE DIAGNOSTIC INFORMATION - SCAN TOOL INFORMATION)SPECIFICATIONSELECTRONIC BRAKE CONTROL MODULE SCAN TOOL INFORMATION (WITH JL7)
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6
Electronic Brake Control Module Scan Tool Information (With JL7)
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Electronic Brake Control Module Scan Tool Information (With JL7)
WARNING: This page is about a different car, the 2010 Cadillac STS. However, it is still accessible from the selected car via links, so may be relevant.
Electronic Brake Control Module Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| ABS Active | No | The scan tool displays Yes or No. The scan tool will display Yes when the ABS is active and No during normal vehicle operation. |
| ABS Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the ABS has failed and No during normal vehicle operation. |
| Battery Voltage Signal | Varies | This displays Volts. This is the current Battery voltage signal. |
| BPP Signal | Varies | The scan tool displays Applied or Released. This is the current state of the Brake Pedal Position Sensor. |
| Brake Fluid Level Status | OK | The scan tool displays Low when the fluid is low and OK when at correct level. |
| Brake Pressure Sensor Input | Varies | This displays Volts. This is the current brake pressure sensor voltage. |
| Delivered Torque | Varies | This displays %. This is the current percentage of torque being delivered |
| DRP Active | No | The scan tool displays Yes or No. The active status of the DRP. Indicates if DRP is currently active. |
| DRP Disabled | No | The scan tool displays Yes or No. The failed status of the DRP. Indicates if the EBCM disabled DRP due to a malfunction. |
| Engine Drag Control Failed | No | The scan tool displays Yes or No. The failed status of the Engine Drag Control Indicates if the ECM disabled Engine Drag Control due to a malfunction. |
| Lateral Accelerometer Signal | m/s 2 | The scan tool displays m/s 2 . This is the current rate of the vehicle acceleration or deceleration as reported by the lateral accelerometer sensor. |
| LF Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver front inlet solenoid. |
| LF Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver front outlet solenoid. |
| LF Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the driver front wheel speed sensor. |
| LR Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver rear inlet solenoid. |
| LR Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver rear outlet solenoid. |
| LR Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the driver rear wheel speed sensor. |
| Panic Brake Assist Failed | No | The scan tool displays Yes or No. The failed status of the Panic Brake Assist indicates if the EBCM disabled Panic Braking due to a malfunction. |
| Pump Motor Commanded Voltage | Varies | This displays Volts. This is the current pump motor feedback voltage. |
| Requested Torque | Varies | This displays %. This is the current percentage of torque being requested. |
| RF Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger front inlet solenoid. |
| RF Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger front outlet solenoid. |
| RF Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the passenger front wheel speed sensor. |
| RR Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger rear inlet solenoid. |
| RR Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger rear outlet solenoid. |
| RR Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the passenger rear wheel speed sensor. |
| Steering Position Signal | Varies | This displays °. This is the current angle of the steering position sensor. |
| TCS Active | No | The scan tool displays Yes or No. This is the state of the traction control system. |
| TCS Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the TCS has failed and No during normal vehicle operation. |
| VSES Active | Varies | The scan tool displays Yes or No. This is the state of the vehicle stability enhancement system. |
| VSES Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the VSES has failed and No during normal vehicle operation. |
| Yaw Rate Sensor Input | °/sec | The scan tool displays °/sec. The scan tool displays the signal received from the Yaw Rate sensor. |
Electronic Brake Control Module Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Automated Bleed | This is used in order to bleed ABS hydraulics. Refer to Antilock Brake System Automated Bleed . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.