Diagnostic Code Index

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Diagnostic Code Index
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC CODE INDEX

DTC Description
DTC B3894 (Gasoline Without LY6)  B3894 5A: Stop Lamp Switch Circuit Plausibility Failure
DTC B3894 (Gasoline With LY6, or Diesel)  B3894 5A: Stop Lamp Switch Circuit Plausibility Failure
DTC C0561 (Gasoline Without LY6)  C0561 F0: System Disabled Information Stored Invalid Serial Data Received
C0561 F1: System Disabled Information Stored Invalid Serial Data Received
DTC C0561 (Gasoline With LY6, or Diesel)  C0561 F0: System Disabled Information Stored Invalid Serial Data Received
C0561 F1: System Disabled Information Stored Invalid Serial Data Received
DTC C0870, C1112, C1113, C1114, or C1119 (Gasoline Without LY6)  C0870 00: Device Voltage Reference Output 1 Circuit
C1112 00: Trailer Brake Control Relay Low Control Circuit
C1113 01: Trailer Brake Control Relay High Control Circuit Short to Battery
C1114 00: Trailer Brake Control Solenoids Control Circuit
C1119 00: Trailer Brake Control Relay Feedback Circuit
DTC C0870, C1112, C1113, C1114, or C1119 (Gasoline With LY6, or Diesel)  C0870 00: Device Voltage Reference Output 1 Circuit
C1112 00: Trailer Brake Control Relay Low Control Circuit
C1113 01: Trailer Brake Control Relay High Control Circuit Short to Battery
C1114 00: Trailer Brake Control Solenoids Control Circuit
C1119 00: Trailer Brake Control Relay Feedback Circuit
DTC C0880, C0890, C1115, C1116, C1117, or C1118 (Gasoline Without LY6)  C0880 00: Device Voltage Reference Output 2 Circuit
C0890 00: Device Voltage Reference Output 3 Circuit
C1115 08: Manual Trailer Brake Apply Request Switch Signal Invalid
C1115 5A: Manual Trailer Brake Apply Request Switch Signal Plausibility Failure
C1116 00: Manual Trailer Brake Apply Request Signal 1
C1117 00: Manual Trailer Brake Apply Request Signal 2
C1118 00: Trailer Brake Control Sensitivity Switch Circuit
C1118 08: Trailer Brake Control Sensitivity Switch Circuit Signal Invalid
DTC C0880, C0890, C1115, C1116, C1117, or C1118 (Gasoline With LY6, or Diesel)  C0880 00: Device Voltage Reference Output 2 Circuit
C0890 00: Device Voltage Reference Output 3 Circuit
C1115 08: Manual Trailer Brake Apply Request Switch Signal Invalid
C1115 5A: Manual Trailer Brake Apply Request Switch Signal Plausibility Failure
C1116 00: Manual Trailer Brake Apply Request Signal 1
C1117 00: Manual Trailer Brake Apply Request Signal 2
C1118 00: Trailer Brake Control Sensitivity Switch Circuit
C1118 08: Trailer Brake Control Sensitivity Switch Circuit Signal Invalid
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.