SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 207 (STARTING SYSTEM)DIAGNOSTIC INFORMATIONDIAGNOSTIC SYSTEM CHECK - ENGINE ELECTRICAL
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6

Diagnostic System Check - Engine Electrical

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Diagnostic System Check - Engine Electrical
WARNING: This page is about a different car, the 2003 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
  1. Perform the Battery Inspection/Test. See BATTERY TESTING & INSPECTION in GENERATORS & REGULATOR article in ELECTRICAL. Does the battery pass the test? If so, go to next step.
  2. Install a scan tool. Turn ON the ignition, with the engine OFF. Does the scan tool power up? If so, go to next step. If not, go to SCAN TOOL DOES NOT POWER UP in BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT.
    NOTE: The engine may start during the following step. Turn OFF the engine as soon as you have observed the Crank power mode.
  3. Access the CLASS 2 POWER MODE in the DIAGNOSTIC CIRCUIT CHECK on the scan tool. Rotate the ignition switch through all positions while observing the Class 2 Power Mode parameter. Does the ignition switch parameter reading match the ignition switch position for all switch positions? If so, go to next step. If not, go to POWER MODE MISMATCH in BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT.
    NOTE: Lack of communication may be because of a partial malfunction of the class 2 serial data circuit or due to a total malfunction of the class 2 serial data circuit. The specified procedure will determine the particular condition.
  4. Turn ON the ignition, with the engine OFF. Attempt to communicate with each of the following modules on the class 2 serial data circuit:
    • Body Control Module (BCM)
    • Powertrain Control Module (PCM)
    Does the scan tool communicate with all modules on the class 2 serial data circuit? If so, go to next step. If not, go to SCAN TOOL DOES NOT COMMUNICATE WITH CLASS 2 DEVICE in BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT.
    NOTE: The symptom list in Symptoms will determine the correct diagnostic procedure to use.
  5. Select the DISPLAY DTCS function for each module. If using a Tech 2, use the CLASS 2 DTC CHECK feature in order to determine which modules have DTCs set. Record all of the displayed DTCs, the DTC status, and the module which set the DTC. Does the scan tool display any DTCs? If so, go to next step. If not, go to SYMPTOMS - ENGINE ELECTRICAL  .
  6. Does the scan tool display any DTCs which begin with a U? If so, go to SCAN TOOL DOES NOT COMMUNICATE WITH CLASS 2 DEVICE in BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT. If not, go to next step.
    NOTE: The presence of DTCs which begin with "U" indicate some other module is not communicating. The specified procedure will collect all the available information before you perform tests.
  7. Does the scan tool display DTC B1000? If so, go to DIAGNOSTIC TROUBLE CODE DEFINITIONS in BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT. If not, go to DIAGNOSTIC TROUBLE CODE DEFINITIONS  .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.