SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2050 (OBJECT DETECTION SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC B0958, B0959, B0960, OR B0961CIRCUIT/SYSTEM TESTING
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6

Circuit/System Testing

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Circuit/System Testing
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

Single Object Alarm Sensor DTC Set

  1. Ignition OFF, disconnect the harness connector at the appropriate object alarm sensor.
  2. Ignition OFF for 30 seconds, test for less than 20 Ξ© between the low reference circuit terminal 2 and ground.
    • If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the rear object sensor control module.
  3. Ignition ON, transmission in REVERSE, test for 8.0-9.0 V between the voltage reference circuit terminal 1 and ground.
    • If greater than the specified range, test the voltage reference circuit for a short to voltage. If the circuit tests normal, replace the rear object sensor control module.
    • If less than the specified range, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear object sensor control module.
  4. Ignition OFF, remove the malfunctioning object alarm sensor and swap locations with another properly functioning object alarm sensor.
  5. Connect the harness connector at both sensors.
  6. Ignition ON, verify DTC is set for the new location in which the malfunctioning object alarm sensor is installed.
    • If the DTC does not set for the new location, test the signal circuit terminal 3 for a short to voltage, short to ground, or an open/high resistance. If the circuit tests normal, replace the rear object sensor control module.
  7. If the DTC sets for the new location in which the malfunctioning object alarm sensor is installed, replace the appropriate object alarm sensor.

Multiple Object Alarm Sensor DTCs Set

  1. Ignition OFF, disconnect the harness connector at each of the object alarm sensors.
  2. Ignition OFF for 30 seconds, test for less than 20 Ξ© between the low reference circuit terminal 2 and ground.
    • If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the rear object sensor control module.
  3. Ignition ON, transmission in REVERSE, test for 8.0-9.0 V between the voltage reference circuit terminal 1 and ground.
    • If greater than the specified range, test the voltage reference circuit for a short to voltage. If the circuit tests normal, replace the rear object sensor control module.
    • If less than the specified range, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear object sensor control module.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.