Electronic Brake Control Module (EBCM) (JL4)

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Electronic Brake Control Module (EBCM) (JL4)
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2009 GMC Savana Special, 2009 GMC Savana Camper Special, 2009 GMC Savana, 2009 Chevrolet RV Cutaway, and 2009 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Electronic Brake Control Module (EBCM) (JL4) - Connector End View
GM1862109Courtesy of GENERAL MOTORS CORP.
Electronic Brake Control Module (EBCM) (JL4)

Pin Wire Circuit Function
1 5 BK 2150 Ground
2 0.5 WH 883 Low Reference
3 0.5 BN 882 Right Rear Wheel Speed Sensor Signal
4 0.5 TN 884 Left Rear Wheel Speed Sensor Signal
5 0.5 OG 885 Low Reference
6 0.5 TN 833 Low Reference
7 0.5 YE 6046 Steering Angle Sensor Phase A
8 0.5 TN 6048 Steering Angle Sensor Phase C
9 0.5 L-GN 6043 Steering Angle Sensor Signal
10-11 - - Not Used
12 0.5 L-BU 5986 Serial Data Communication Enable
13 5 RD/BK 442 Battery Positive Voltage
14-15 - - Not Used
16 0.5 OG/BK 6045 Low Reference
17 0.5 D-GN 872 Right Front Wheel Speed Sensor Signal
18 - - Not Used
19 0.5 GY/BK 1337 12-Volt Reference
20 0.5 D-BU 6047 Steering Angle Sensor Phase B
21 0.5 WH/BK 6436 CAN Bus Low Terminated Serial Data
22 - - Not Used
23 0.5 TN 2501 High Speed GMLAN Serial Data Bus (-)
24 0.5 TN 2501 High Speed GMLAN Serial Data Bus (-)
25 3 BK 2150 Ground
26-27 - - Not Used
28 0.5 L-BU 830 Left Front Wheel Speed Sensor Signal
29 0.5 YE 873 Low Reference
30 0.5 BK/PU 7499 Low Reference
31 0.5 GY 6044 5-Volt Reference
32 0.5 YE/BK 1827 Vehicle Speed Signal
33 0.5 BN/WH 6437 CAN Bus High Terminated Serial Data
34-35 - - Not Used
36 0.5 TN/BK 2500 High Speed GMLAN Serial Data Bus (+)
37 0.5 TN/BK 2500 High Speed GMLAN Serial Data Bus (+)
38 3 RD/WH 1640 Battery Positive Voltage
Connector Part Information 
  • OEM: 13528146
  • Service: See Catalog
  • Description: 38-Way F 2.8 Series Sealed (BK)
Terminal Part Information 
  • Pins: 1, 13
  • Terminal/Tray: 7116-4142-02/10
  • Core/Insulation Crimp: D/3
  • Release Tool/Test Probe: 12094430/J-35616-42 (RD)
  • Pins: 2-9, 12, 16, 17, 19, 20-24, 28-33, 36, 37
  • Terminal/Tray: 7116-3703-02
  • Core/Insulation Crimp: See Terminal Repair Kit
  • Release Tool/Test Probe: See Terminal Repair Kit
  • Pins: 25, 38
  • Terminal/Tray: 15304720/19
  • Core/Insulation Crimp: 4/5
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.