Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1856 (FRONT SUSPENSION SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6
Fastener Tightening Specifications
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2009 GMC Savana Special, 2009 GMC Savana Camper Special, 2009 GMC Savana, 2009 Chevrolet RV Cutaway, and 2009 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Brake Hose Bracket to Steering Knuckle Bolt | 10 N.m | 88 lb in |
| Brake Hose Bracket to Upper Control Arm Bolt | 10 N.m | 88 lb in |
| Hub and Bearing to Steering Knuckle Mounting Bolts | 180 N.m | 133 lb ft |
| Lower Ball Joint Retaining Nut | 100 N.m | 74 lb ft |
| Lower Control Arm to Frame Mounting Nuts | ||
|
155 N.m | 114 lb ft |
|
120 N.m + 175° | 89 lb ft + 175° |
|
120 N.m + 175° | 89 lb ft + 175° |
| Outer Tie Rod Retaining Nut | 63 N.m | 47 lb ft |
| Shock Absorber Lower Retaining Bolts | ||
|
25 N.m | 18 lb ft |
|
80 N.m | 59 lb ft |
| Shock Absorber Upper Retaining Nut | 22 N.m | 16 lb ft |
| Stabilizer Shaft Insulator Clamp | ||
|
25 N.m | 18 lb ft |
|
50 N.m | 37 lb ft |
|
25 N.m | 18 lb ft |
| Stabilizer Shaft Link Bolt | 11 N.m | 97 lb in |
| Torsion Bar Support Mounting Bolts | 95 N.m | 70 lb ft |
| Upper Ball Joint Retaining Nut | 50 N.m | 37 lb ft |
| Upper Control Arm Mounting Nuts | 175 N.m | 129 lb ft |
| Wheel Drive Shaft Nut | 210 N.m | 155 lb ft |
| Wheel Speed Sensor Retaining Bolt | 18 N.m | 13 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.