Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1653 (TRAILER BRAKE CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDIAGNOSTIC CODE INDEX
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6
Diagnostic Code Index
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Diagnostic Code Index
WARNING: This page is about a different car, the 2009 GMC Sierra, 2009 GMC Cab & Chassis Sierra, 2009 Chevrolet Silverado, and 2009 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| DTC B3894 | B3894 5A: Stop Lamp Switch Circuit Plausibility Failure |
| DTC C0561 | C0561 F0: System Disabled Information Stored Invalid Serial Data Received C0561 F1: System Disabled Information Stored Invalid Serial Data Received |
| DTC C056D or C056E | C056D 33: ECU Hardware Performance Special Memory Failure C056D 34: ECU Hardware Performance RAM Failure C056D 35: ECU Hardware Performance ROM Failure C056D 36: ECU Hardware Performance EEPROM Failure C056D 39: ECU Hardware Performance Internal Electronic Failure C056E 41: ECU Software Performance Operational Software/Calibration Set Not Programmed |
| DTC C0800 | C0800 03: Device Power Circuit Voltage Below Threshold C0800 07: Device Power Circuit Voltage Above Threshold |
| DTC C0845 | C0845 03: Device Ignition 1 Circuit Voltage Below Threshold |
| DTC C0870, C1112, C1113, C1114, or C1119 | C0870 00: Device Voltage Reference Output 1 Circuit C1112 00: Trailer Brake Control Relay Low Control Circuit C1113 01: Trailer Brake Control Relay High Control Circuit Short to Battery C1114 00: Trailer Brake Control Solenoids Control Circuit C1119 00: Trailer Brake Control Relay Feedback Circuit |
| DTC C0880, C0890, C1115, C1116, C1117, or C1118 | C0880 00: Device Voltage Reference Output 2 Circuit C0890 00: Device Voltage Reference Output 3 Circuit C1115 08: Manual Trailer Brake Apply Request Switch Signal Invalid C1115 5A: Manual Trailer Brake Apply Request Switch Signal Plausibility Failure C1116 00: Manual Trailer Brake Apply Request Signal 1 C1117 00: Manual Trailer Brake Apply Request Signal 2 C1118 00: Trailer Brake Control Sensitivity Switch Circuit C1118 08: Trailer Brake Control Sensitivity Switch Circuit Signal Invalid |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.