Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1250 (POWER STEERING SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6
Fastener Tightening Specifications
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2008 Chevrolet Malibu Classic. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Electronic Power Steering (EPS) Motor to Steering Column Bolts | 9 N.m | 80 lb in |
| Electronic Power Steering (EPS) Power Steering Gear Mounting Bolt | 70 N.m | 52 lb ft |
| Hydraulic Power Steering (HPS) Power Steering Gear Mounting Bolt | 110 N.m | 81 lb ft |
| Inner Tie Rod | 100 N.m | 74 lb ft |
| Intermediate Steering Shaft to Steering Gear Pinch Bolt | 49 N.m | 36 lb ft |
| Outer Tie Rod Castle Nut | ||
|
25 N.m | 18 lb ft |
|
+ 90° | |
| Power Steering Flow Control Valve Fitting | 75 N.m | 55 lb ft |
| Power Steering Gear Adjuster Plug Lock Nut | 68 N.m | 50 lb ft |
| Power Steering Gear Cylinder Line Nuts | 31 N.m | 23 lb ft |
| Power Steering Gear Cylinder Line Retaining Plate Bolt | 15 N.m | 12 lb ft |
| Power Steering Gear Inlet Pipe-to-Power Steering Pump Fitting | 27 N.m | 20 lb ft |
| Power Steering Gear Inlet/Outlet Pipe Clip to Generator Stud Retaining Nut | 5 N.m | 45 lb in |
| Power Steering Gear Inlet/Outlet Pipe Retaining Bolt | 27 N.m | 20 lb ft |
| Power Steering Pump Bolt | 25 N.m | 18 lb ft |
| Transaxle Bracket to Cradle/Frame Nut | 50 N.m | 37 lb ft |
| Transaxle Mount Through Bolt (4T45-E) | 90 N.m | 66 lb ft |
| Transaxle Mount Through Bolt (4T65-E) | 50 N.m | 37 lb ft |
| Transaxle Mount to Transaxle Bolt (4T45-E) | 90 N.m | 66 lb ft |
| Transaxle Mount to Transaxle Bolt (4T65-E) | 50 N.m | 37 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.