SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1033 (DISC BRAKE SYSTEM)SPECIFICATIONSDISC BRAKE COMPONENT SPECIFICATIONS
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6

Disc Brake Component Specifications

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Disc Brake Component Specifications
WARNING: This page is about a different car, the 2007 GMC Sierra and 2007 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Disc Brake Component Specifications

Application Specification
Metric English
Front Brakes JF3, JF7
  • Rotor Discard Thickness*
 28.0 mm 1.10 in
  • Rotor Minimum Allowable Thickness After Refinish
 28.0 mm 1.10 in
  • Rotor Thickness (new)
 30.0 mm 1.181 in
  • Rotor Maximum Allowable Lateral Runout
 0.05 mm 0.002 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Front Brakes JD9, JH6, JH7
  • Rotor Discard Thickness*
 36.50 mm 1.437 in
  • Rotor Minimum Allowable Thickness After Refinish
 37.0 mm 1.457 in
  • Rotor Thickness (new)
 38.0 mm 1.496 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Rear Brakes JD9
  • Rotor Discard Thickness*
 18.0 mm 0.709 in
  • Rotor Minimum Allowable Thickness After Refinish
 18.5 mm 0.7282 in
  • Rotor Thickness (new)
 20.0 mm 0.787 in
  • Rotor Maximum Allowable Lateral Runout
 0.25 mm 0.010 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.009 mm 0.0004 in
Rear Brakes JH6
  • Rotor Discard Thickness*
 27.5 mm 1.083 in
  • Rotor Minimum Allowable Thickness After Refinish
 28.0 mm 1.102 in
  • Rotor Thickness (new)
 30.0 mm 1.181 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
Rear Brakes JH7
  • Rotor Discard Thickness*
 28.5 mm 1.122 in
  • Rotor Minimum Allowable Thickness After Refinish
 29.0 mm 1.142 in
  • Rotor Thickness (new)
 30.0 mm 1.181 in
  • Rotor Maximum Allowable Lateral Runout
 0.13 mm 0.005 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Allowable Thickness Variation
 0.025 mm 0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace any rotor that does not meet the minimum thickness specifications.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.