SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008AVEO LT, AUTOMATICREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESYSTEMENGINE CONTROLS AND FUEL - 1.6L - INTRODUCTION (2 OF 2)COMPONENT LOCATORENGINE CONTROLS CONNECTOR END VIEWS (HATCHBACK)
2008 Chevrolet Aveo LT, Automatic

Engine Controls Connector End Views (Hatchback)

2008 Chevrolet Aveo LT, AutomaticSECTION Engine Controls Connector End Views (Hatchback)
Accelerator Pedal Position (APP) Sensor

GM1468516Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 174923
  • 6-Way F (BK)
Pin Wire Color Circuit No. Function
1 D-BU 1161 Accelerator Pedal Position Signal 1
2 D-GN/WH 718 Low Reference
3 WH 1162 Accelerator Pedal Position Signal 2
4 L-BU 645 Low Reference
5 GY 474 5-Volt Reference
6 GY/BK 596 5-Volt Reference
Camshaft Position (CMP) Sensor

GM1467004Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 85205-1
  • 3-Way F JR Power Timer 3P Housing Assembly (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 BK/WH 51 Ground
3 L-BU/BK 1748 Camshaft Position (CMP) Sensor Signal
Crankshaft Position Sensor (CKP)

GM1467004Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 85205-1
  • 3-Way F JR Power Timer 3P Housing Assembly (BK)
Pin Wire Color Circuit No. Function
1 D-BU/WH 1869 Crankshaft Position (CKP) Sensor Signal
2 YE/BK 1868 Low Reference
3 BK/WH 51 Ground
Throttle Actuator Control (TAC)

GM1466987Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 15326835
  • 8-Way F Metri-Pack 150 Series Sealed (BK)
Pin Wire Color Circuit No. Function
1 PU 427 5-Volt Reference
2 BN/BK 486 Throttle Position Sensor Signal 2
3 WH 425 Throttle Position Sensor Signal 1
4 L-BU 426 Low Reference
5 L-BU 581 ETC (- )
6-7 - - Not Used
8 BU/BK 582 ETC (+)
Engine Coolant Temperature (ECT) Sensor

GM62426Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12040753
  • 2-Way F Metri-Pack 150 Series Sealed, Pull To Seat (BK)
Pin Wire Color Circuit No. Function
A L-GN 410 Engine Coolant Temperature (ECT) Sensor Signal
B WH 808 Low Reference
Evaporative Emissions (EVAP) Canister Purge Solenoid Valve

GM684795Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12052643
  • 2-Way F Metri-Pack 150 Series Sealed (RD)
Pin Wire Color Circuit No. Function
A WH 452 EVAP Canister Purge Valve Solenoid Control
B PK/D-BU 1733 Ignition 1 Voltage
Evaporative Emissions (EVAP) Canister Vent Solenoid

GM1481266Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AK 32229
  • 2-Way F (BN)
Pin Wire Color Circuit No. Function
1 YE 1578 EVAP Canister Vent Solenoid Control
2 BN 1733 Ignition 1 Voltage
Exhaust Gas Recirculation (EGR) Valve

GM1468386Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12110790
  • 5-Way F Metri-Pack 150 Series Sealed (GY)
Pin Wire Color Circuit No. Function
A D-BU 436 Exhaust Gas Recirculation (EGR) Valve Control
B WH 813 Low Reference
C D-GN 435 Exhaust Gas Recirculation (EGR) Valve Position Sensor Signal
D L-BU 416 5-Volt Reference
E PK 1733 Ignition 1 Voltage
Fuel Injector 1

GM1466998Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 368468-1
  • 2-Way F Injector Plug Assembly (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 YE 1747 Fuel Injector 1 Control
Fuel Injector 2

GM1466998Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 368468-1
  • 2-Way F Injector Plug Assembly (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 BN/BK 1746 Fuel Injector 2 Control
Fuel Injector 3

GM1466998Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 368468-1
  • 2-Way F Injector Plug Assembly (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 BN/WH 1745 Fuel Injector 3 Control
Fuel Injector 4

GM1466998Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 368468-1
  • 2-Way F Injector Plug Assembly (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 L-GN 1744 Fuel Injector 4 Control
Fuel Pump/Sender

GM1468528Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 36159-1
  • 6-Way F Fuel Pump 6 POS Connector Assembly (BN)
Pin Wire Color Circuit No. Function
1 GY 1936 Fuel Level Sensor Signal
2 BK 850 Ground
3 BN 1723 Fuel Pump Supply Voltage
4 BK 850 Ground
5 PU 172 Low Fuel Indicator Control
6 L-BU 1937 Low Reference
Fuel Tank Pressure (FTP) Sensor

GM516611Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12059595
  • 3-Way F Metri-Pack 150 Series Sealed (BK)
Pin Wire Color Circuit No. Function
A GY/D-GN 1029 Low Reference
B L-BU 1030 Fuel Tank Pressure Sensor Signal
C WH 1031 5-Volt Reference
Heated Oxygen Sensor (HO2S) 1

GM1466979Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • 174257-2
  • 4-Way F Econoseal J-Mark II Series, Sealed (BK)
Pin Wire Color Circuit No. Function
1 D-BU/BK 429 Heated Oxygen Sensor (HO2S) 1 Signal
2 BN 50 Heated Oxygen Sensor (HO2S) 1 Heater Control
3 WH 428 Heated Oxygen Sensor (HO2S) 1 Low Reference
4 PK/D-BU 1734 Main Relay Output
Heated Oxygen Sensor (HO2S) 2

GM1940131Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PB625-04027
  • 4-Way F NMWP04F-B Series, Sealed (BK)
Pin Wire Color Circuit No. Function
1 L-GN 413 Heated Oxygen Sensor (HO2S) 2 Signal
2 BN 1671 Heated Oxygen Sensor (HO2S) 2 Heater Control
3 D-GN/BK 1670 Heated Oxygen Sensor (HO2S) 2 Low Reference
4 PK/D-BU 1734 Main Relay Output
Ignition Coil (IC) Module

GM516611Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12059595
  • 3-Way F Metri-Pack 150 Series Sealed (BK)
Pin Wire Color Circuit No. Function
A OG 423 Ignition Coil (IC) Timing Control 2 and 3
B PK/D-BU 539 Ignition 1 Voltage
C WH 406 Ignition Coil (IC) Timing Control 1 and 4
Intake Air Temperature (IAT) Sensor

GM1467003Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 85202-1
  • 2-Way JR Power Timer 2P Housing Assembly (BK)
Pin Wire Color Circuit No. Function
1 L-BU 468 Intake Air Temperature (IAT) Sensor Signal
2 WH 808 Low Reference
Intake Manifold Tuning (IMT) Solenoid Valve

GM1466982Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 174352-2
  • 2-Way F Econoseal J Mark II + Connector Plug Housing (BK)
Pin Wire Color Circuit No. Function
1 PK 1733 Ignition 1 Voltage
2 YE 492 Intake Manifold Tuning Valve Solenoid Control
Intake Manifold Tuning (IMT) Valve Position Sensor

GM1467094Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 1717888
  • 3-Way F (BK)
Pin Wire Color Circuit No. Function
1 L-BU 469 5-Volt Reference
2 YE 45 Intake Manifold Tuning (IMT) Valve Position Sensor
3 WH 433 Low Reference
Knock Sensor (KS)

GM1467003Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • AMP 368215-1
  • 2-Way JPT 3P Assembly for Knock Sensor (GY)
Pin Wire Color Circuit No. Function
1 L-BU 496 Knock Sensor (KS) Signal
2 D-BU/WH 1876 Low Reference
Manifold Absolute Pressure (MAP) Sensor

GM516611Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12059595
  • 3-Way F Metri-Pack 150 Series Sealed (BK)
Pin Wire Color Circuit No. Function
A WH 433 Low Reference
B L-BU 432 Manifold Absolute Pressure (MAP) Sensor Signal
C L-BU 469 5-Volt Reference
Rough Road Sensor

GM73223Courtesy of GENERAL MOTORS CORP.
Connector Part Information
  • PED 12162185
  • 3-Way F Metri-Pack 150.2 Series Sealed, Pull To Seat (BK)
Pin Wire Color Circuit No. Function
A L-BU 1937 Low Reference
B D-GN 602 Rough Road Sensor Signal
C WH 1031 5-Volt Reference
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.