Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1846 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - T-V)
2006 Chevrolet Suburban K2500, 6.0 U
Section 1846 (Wiring Systems And Power Management - Component Connector End Views - T-V)
2006 Chevrolet Suburban K2500, 6.0 USECTION Section 1846 (Wiring Systems And Power Management - Component Connector End Views - T-V)
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
- Component Connector End Views - T Through V
- Tail/Stop and Turn Signal Lamp - Lower Left
- Tail/Stop and Turn Signal Lamp - Lower Right
- Tail/Stop and Turn Signal Lamp - Upper Left
- Tail/Stop and Turn Signal Lamp - Upper Right
- Theft Deterrent Module (TDM)
- Throttle Body (HP2)
- Throttle Body (Gas except HP2)
- Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Valve (MW7)
- Torque Converter Clutch (TCC) Pulse Width Modulated (PWM) Solenoid Valve (M30)
- Torque Converter Clutch (TCC) Solenoid Valve (M30)
- Trailer Brake Control Module (JL1 except 31 Series)
- Trailer Brake Control Module (JL1 with 31 Series)
- Trailer Brake Control Relay (JL1)
- Trailer Brake Control Switch (JL1)
- Trailer Connector (except MEX or EXP)
- Trailer Stop/Turn Relay (TZ0)
- Transfer Case 2/4 Wheel Drive Actuator Position Sensor (NQH)
- Transfer Case Encoder Motor (NQF or NQH)
- Transfer Case Shift Control Module X1 (NQF or NQH)
- Transfer Case Shift Control Module X2 (NQF or NQH)
- Transfer Case Shift Control Module X3 (NQF or NQH)
- Transfer Case Shift Control Switch (NQF or NQH)
- Transfer Case Shift Control Switch (NQG)
- Transmission Control Module (TCM) (M30)
- Transmission Control Module (TCM) (MW7)
- Transmission Power Inverter Module (3 Phase) Cable Cover (HP2)
- Turbocharger Vane Position Control Solenoid Valve (Diesel)
- Turbocharger Vane Position Sensor (Diesel)
- Turn Signal/Multifunction Switch X1
- Turn Signal/Multifunction Switch X2
- Turn Signal/Multifunction Switch X3
- Valve Lifter Oil Manifold (VLOM) Assembly (LMG, LC9, LZ1 or L96)
- Vehicle Communication Interface Module (VCIM) X1 (UE1)
- Vehicle Communication Interface Module (VCIM) X2 (UE1)
- Vehicle Communication Interface Module (VCIM) X3 (UE1 with UUL or UUK)
- Vehicle Inclination Sensor (SPO Alarm)
- Vehicle Shock Sensor (SPO Alarm)
- Vehicle Speed Sensor (VSS) (M30, TZ0, MYC and MW7or M99 with NQG or NQF)
- Vehicle Speed Sensor (VSS) (MW7 except NQG or NQF)
- Video Display (U42)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.