SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1827 (COMPONENT LOCATIONS - ELECTRICAL CENTER IDENTIFICATION VIEWS)ELECTRICAL CENTER IDENTIFICATION VIEWSJUNCTION BLOCK - RIGHT I/P X3
2006 Chevrolet Suburban K2500, 6.0 U

Junction Block - Right I/P X3

2006 Chevrolet Suburban K2500, 6.0 USECTION Junction Block - Right I/P X3
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Junction Block - Right I/P X3
GM1667402Courtesy of GENERAL MOTORS CORP.
Junction Block - Right I/P X3

Pin Wire Circuit Function
A1 0.8 D-GN 117 Right Front Speaker Output (-) (UQA)
0.5 D-GN 117 Right Front Speaker Output (-) (UQ3 or UQ5)
A2 0.8 L-GN 200 Right Front Speaker Output (+) (UQA)
0.5 L-GN 200 Right Front Speaker Output (+) (UQ3 or UQ5)
A3 0.35 BK 1850 Ground (except AN3 or DL3)
A4 0.5 D-BU/WH 1315 Right Front Turn Signal Lamp Supply Voltage (DL3 or DPN)
0.35 L-BU 244 Passenger Door Lock Switch Lock Signal (AU3 without YE9)
A5 0.35 TN/WH 746 Right Front Door Ajar Switch Signal (except AN3 or DL3)
A6 1 GY 295 Door Lock Actuator Lock Control (AU3 without AN3 or DL3)
A7 3 BK 1050 Ground (A31, AN3, DL3, DL8 or DPN)
B1 0.35 D-GN 5060 Low Speed GMLAN Serial Data (AN3 or DL3)
B2 0.8 RD/WH 240 Battery Positive Voltage (AN3 or DL3)
B3 1 TN 294 Door Lock Actuator Unlock Control (AU3 without AN3 or DL3)
B4 2 RD/WH 1340 Battery Positive Voltage (A31)
0.35 D-BU 245 Passenger Door Lock Switch Unlock Signal (AU3 without YE9)
B5 0.35 BN/WH 230 Instrument Panel Lamps Dimming Control (AU3 without AN3 or DL3)
B6-B7 - - Not Used
Connector Part Information 
  • Harness: Right Front Door
  • OEM: 15467622
  • Service: 19115664
  • Description: 14-Way F GT 150/280 Series (L-GY)
Terminal Part Information 
  • Pins: A1 (UQ3 or UQ5)
  • Pins: A4, B1, B4
  • Terminal/Tray: 15304711/8
  • Core/Insulation Crimp: - E/A
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
  • Pins: A1 (UQA)
  • Terminal/Tray: 15304711/8
  • Core/Insulation Crimp: - 2/A
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
  • Pins: A2 (UQ3 or UQ5)
  • Pins: A3, A5, B5, B6
  • Terminal/Tray: 12191812/19
  • Core/Insulation Crimp: - E/C
  • Release Tool/Test Probe: 15315247/J-35616-2A (GY)
  • Pins: A2 (UQA)
  • Pins: A6, B2, B3
  • Terminal/Tray: 12191812/19
  • Core/Insulation Crimp: - C/A
  • Release Tool/Test Probe: 15315247/J-35616-2A (GY)
  • Pins: A7, B4, A7
  • Terminal/Tray: 15304713/19
  • Core/Insulation Crimp: Pins A7, B4, B4 - 4/4
  • Core/Insulation Crimp: Pins A7 - F/D
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.