Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1321 (BATTERY, CHARGING SYSTEM AND STARTING SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2006 Chevrolet Suburban K2500, 6.0 U
Fastener Tightening Specifications
2006 Chevrolet Suburban K2500, 6.0 USECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2008 GMC Yukon XL, 2008 GMC Yukon, 2008 Chevrolet Tahoe, 2008 Chevrolet Suburban, and 2008 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Battery Cable Channel Nut | 3 N.m | 27 lb in |
| Battery Hold Down Retainer Bolt | 25 N.m | 18 lb ft |
| Battery Tray to Battery Tray Bracket Nut | 9 N.m | 80 lb in |
| Battery Tray to Front Fender Inner Panel Nut | 9 N.m | 80 lb in |
| Battery Tray Front Support Bolt | 9 N.m | 80 lb in |
| Engine Ground Strap to Front Plenum Panel Nut | 9 N.m | 80 lb in |
| Engine Ground Strap to Left Cylinder Head Bolt | 16 N.m | 12 lb ft |
| Engine Wiring Harness Clip to Generator Bracket Bolt | 9 N.m | 80 lb in |
| Engine Wiring Harness Lead Nut | 3.4 N.m | 30 lb in |
| Forward Lamp Wiring Harness Ground Bolt | 25 N.m | 18 lb ft |
| Front Fender Rear Upper Brace Bolt | 9 N.m | 80 lb in |
| Generator Battery Jumper Cable to Generator Nut | 9 N.m | 80 lb in |
| Generator Battery Jumper Cable to Mega Fuse Nut | 9 N.m | 80 lb in |
| Generator Bolt | 55 N.m | 41 lb ft |
| Generator Bracket Bolt | 50 N.m | 37 lb ft |
| Negative Battery Cable Nut | 5 N.m | 44 lb in |
| Negative Battery Cable Stud | 25 N.m | 18 lb ft |
| Oil Pan Skid Plate Bolt | 28 N.m | 21 lb ft |
| Starter Bolt | 50 N.m | 37 lb ft |
| Starter Solenoid Cable to Battery Nut | 5 N.m | 44 lb in |
| Starter Solenoid Cable to Starter Nut | 9 N.m | 80 lb in |
| Transmission Cover Bolt | 9 N.m | 80 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.