Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1296 (COMPONENT LOCATIONS)FRONT OF VEHICLE/ENGINE COMPARTMENT COMPONENT VIEWS
2006 Chevrolet Suburban K2500, 6.0 U
Front of Vehicle/Engine Compartment Component Views
2006 Chevrolet Suburban K2500, 6.0 USECTION Front of Vehicle/Engine Compartment Component Views
WARNING: This page is about a different car, the 2008 Cadillac CTS. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 1 | Turn Signal Lamp - Right Front |
| 2 | Daytime Running Lamp (DRL) - Right (TT6/TT7/TT8) |
| 3 | Headlamp - Right High/Low Beam |
| 4 | Fog Lamp - Right Front |
| 5 | Side Marker Tube-Right Front |
| 6 | Repeater Lamp - Right (T90) |
| 7 | Turn Signal Lamp - Left Front |
| 8 | Repeater Lamp - Left (T90) |
| 9 | Side Marker Tube-Left Front |
| 10 | Headlamp - Left High/Low Beam |
| 11 | Fog Lamp-Left |
| 12 | Daytime Running Lamp (DRL) - Left (TT6/TT7/TT8) |
| Callout | Component Name |
|---|---|
| 1 | Headlamp Ballast - Right (TT6/TT7/TT8) |
| 2 | Headlamp Motor - Right (TR7+TT6/TT7/TT8) |
| 3 | Headlamp Module (TT6/TT7/TT8) |
| 4 | Headlamp Motor - Left (TR7+TT6/TT7/TT8) |
| 5 | Headlamp - Ballast Left (TT6/TT7/TT8) |
| 6 | Headlamp Leveling Sensor - Right Front (TR7) |
| Callout | Component Name |
|---|---|
| 1 | Brake Fluid Level Switch |
| 2 | Mass Air Flow (MAF) / Intake Air Temperature (IAT) Sensor (LLT) |
| 3 | Fuse Block - Underhood |
| 4 | Engine Control Module (ECM) |
| 5 | Electronic Brake Control Module (EBCM) |
| Callout | Component Name |
|---|---|
| 1 | Coolant Surge Tank (RHD) |
| 2 | Coolant Surge Tank (LHD) |
| Callout | Component Name |
|---|---|
| 1 | Clutch Pedal Position (CPP) Switch |
| 2 | Clutch Master Cylinder |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.