Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1079 (FRONT DRIVE AXLE)COMPONENT LOCATORFRONT DRIVE AXLE DISASSEMBLED VIEWS (8.25 INCH (AWD))
2006 Chevrolet Suburban K2500, 6.0 U
Front Drive Axle Disassembled Views (8.25 Inch (AWD))
2006 Chevrolet Suburban K2500, 6.0 USECTION Front Drive Axle Disassembled Views (8.25 Inch (AWD))
WARNING: This page is about a different car, the 2007 GMC Sierra and 2007 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 1 | Output Shaft |
| 2 | Pinion Bearing Spacer |
| 3 | Pinion Head Bearing Assembly |
| 4 | Pinion Shim |
| 5 | Stem Pinion |
| 6 | Pinion Flange Nut |
| 7 | Pinion Flange Washer |
| 8 | Pinion Flange Assembly |
| 9 | Pinion Seal |
| 10 | Pinion Tail Bearing Assembly |
| 11 | Carrier Housing |
| 12 | Output Shaft Seal Assembly |
| 13 | Output Shaft |
| 14 | Drain Plug Assembly |
| 15 | Drain Plug Washer |
| 16 | Fill Plug Assembly |
| 17 | Fill Plug O-ring Seal |
| 18 | Carrier Locator Pin |
| 19 | Vent Connector |
| 20 | Differential Case |
| 21 | Ring Gear |
| 22 | Output Shaft Bearing Assembly |
| 23 | 8-Point Lock Ring |
| 24 | Sleeve and Insert Assembly |
| 25 | Differential Case Bearing Assembly |
| 26 | Differential Cross Pin Lock Pin |
| 27 | Differential Pinion Thrust Washer |
| 28 | Differential Pinion Gear |
| 29 | Differential Side Gear Thrust Washer |
| 30 | Differential Side Gear |
| 31 | Output Shaft Snap Ring |
| 32 | Differential Pinion Gear |
| 33 | Differential Pinion Thrust Washer |
| 34 | Output Shaft Snap Ring |
| 35 | Differential Side Gear |
| 36 | Differential Side Gear Thrust Washer |
| 37 | Differential Cross Pin |
| 38 | Ring Gear Bolt |
| 39 | 8-Point Lock Ring |
| 40 | Sleeve and Insert Assembly |
| 41 | Differential Case Bearing Assembly |
| 42 | Carrier Gasket |
| 43 | Carrier Cover |
| 44 | Tube Locator Pin |
| 45 | Carrier Bolt |
| 46 | Tube Bolt |
| 47 | Output Shaft Seal |
| 48 | Output Shaft Bearing Assembly |
| 49 | Tube |
| 50 | Tube Gasket |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.