Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN K1500, 5.3 ZREPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESANTI-LOCK BRAKESANTILOCK BRAKE SYSTEM WITH TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM
2006 Chevrolet Suburban K1500, 5.3 Z
Antilock Brake System With Traction Control System & Stability Control System
2006 Chevrolet Suburban K1500, 5.3 ZSECTION Antilock Brake System With Traction Control System & Stability Control System
- Specifications
- Schematic and Routing Diagrams
- Component Locator
- ABS Component Views
- ABS Connectors
- Electronic Brake Control Module (EBCM) - C1 (w/o JL4)
- Electronic Brake Control Module (EBCM) - C2 (w/o JL4)
- Electronic Brake Control Module (EBCM) (w/JL4)
- Precharge Pump
- Stop Lamp Switch (w/o JL4)
- Stop Lamp Switch (w/JL4)
- Traction Control Switch (w/o JL4)
- Traction Control Switch (w/JL4)
- Wheel Speed Sensor (WSS) - LF
- Wheel Speed Sensor (WSS) - RF
- Wheel Speed Sensor (WSS) - LR (10 Series w/JL4 )
- Wheel Speed Sensor (WSS) - RR (10 Series w/JL4)
- Wheel Speed Sensor (WSS) - RR (20 Series w/JL4)
- YAW and Lateral Acceleration Sensor
- Diagnostic Information and Procedures
- Diagnostic Code Index
- Diagnostic Starting Point - Anti-Lock Brake System
- Scan Tool Output Controls (W/O JL4 or NW7)
- Scan Tool Output Controls (W/JL4)
- Scan Tool Output Controls (W/NW7)
- Scan Tool Data List
- Scan Tool Data Definitions
- DTC C0035 or C0040
- DTC C0045 or C0050
- DTC C0110
- DTC C0131
- DTC C0161
- DTC C0186
- DTC C0196
- DTC C0201
- DTC C0220
- DTC C0221-C0227 (W/O JL4)
- DTC C0221-C0227 (W/JL4)
- DTC C0228
- DTC C0229 (W/JL4)
- DTC C0229 (W/O JL4)
- DTC C0235-C0237 or P0609
- DTC C0238
- DTC C0240
- DTC C0241-C0243
- DTC C0244 (W/O JL4)
- DTC C0244 (W/JL4)
- DTC C0245 (W/JL4)
- DTC C0245 (W/O JL4)
- DTC C0246-C0254
- DTC C0265 or C0266
- DTC C0267 or C0268
- DTC C0269 or C0274
- DTC C0271-C0273, C0284
- DTC C0279 (W/O JL4)
- DTC C0279 (W/JL4)
- DTC C0281
- DTC C0283 (W/JL4)
- DTC C0283 (W/O JL4)
- DTC C0287, P1644, or P1689
- DTC C0290 or C0292 (W/O JL4)
- DTC C0290 or C0292 (W/JL4)
- DTC C0291
- DTC C0297
- DTC C0298 or P0856
- DTC C0455
- DTC C0472 or C0473
- DTC C0550
- DTC C0558
- Symptoms - Anti-Lock Brake System
- ABS Indicator Always On
- ABS Indicator Inoperative
- Stability System Disabled Indicator Always On
- Traction Off Indicator Always On
- Traction Off Indicator Inoperative
- Traction Control System Poor Performance
- Vehicle Stability Enhancement System Poor Performance
- Brake Pressure Modulator Valve Hydraulic Testing
- Repair Instructions
- ABS Automated Bleed Procedure (w/o JL4)
- ABS Automated Bleed Procedure (W/JL4)
- Electronic Brake Control Module Replacement (w/o JL4)
- Electronic Brake Control Module Replacement (w/JL4)
- Brake Pressure Modulator Valve (BPMV) Replacement (w/JL4)
- Brake Pressure Modulator Valve (BPMV) Replacement (w/o JL4)
- Brake Pressure Modulator Valve Pre-Charge Pump Replacement
- Wheel Speed Sensor Replacement - Front (2 Wheel Drive)
- Wheel Speed Sensor Replacement - Front (4 Wheel Drive)
- Wheel Speed Sensor Replacement - Rear
- Wheel Speed Sensor Ring Replacement - Rear
- Traction Control Switch Replacement (Stabilitrak)
- Yaw Rate Reference Table Reset Procedure
- Yaw Rate Sensor/Lateral Accelerometer Replacement
- Description and Operation
- ABS Description and Operation (W/JL4)
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.