Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 932 (ANTILOCK BRAKE SYSTEM, TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC C0161 (OVER 8600 GVW)TEST DESCRIPTION
2006 Chevrolet Suburban C2500, 6.0 U
Test Description
2006 Chevrolet Suburban C2500, 6.0 USECTION Test Description
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
The numbers below refer to the step numbers on the diagnostic table.
- 4: This step tests for a shorted stop lamp switch.
- 5: This step tests for an open stop lamp switch.
DTC C0161 (Over 8600 GVW)
| Step | Action | Yes | No |
|---|---|---|---|
| Schematic Reference: Antilock Brake System Schematics | |||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
| 2 |
|
Go to Step 3 | Go to Step 5 |
| 3 |
|
Go to Diagnostic Aids | Go to Step 4 |
| 4 |
|
Go to Step 9 | Go to Step 7 |
| 5 |
|
Go to Step 9 | Go to Step 6 |
| 6 | Test the ignition 3 voltage circuit and the TCC brake switch signal circuit for an open or a short to ground. Refer to Circuit Testing
and to Wiring Repairs
. Did you find and correct the condition? |
Go to Step 12 | Go to Step 8 |
| 7 | Test the TCC brake switch signal circuit for a short to voltage. Refer to Circuit Testing
and to Wiring Repairs
. Did you find and correct the condition? |
Go to Step 12 | Go to Step 8 |
| 8 | Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
. Did you find and correct the condition? |
Go to Step 12 | Go to Step 10 |
| 9 | Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
. Did you find and correct the condition? |
Go to Step 12 | Go to Step 11 |
| 10 | Replace the EBCM. Refer to Control Module References
for replacement, setup and programming. Did you complete the replacement? |
Go to Step 12 | - |
| 11 | Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement (Adjustable Pedal)
or Stop Lamp Switch Replacement (Non-Adjustable Pedal)
. Did you complete the replacement? |
Go to Step 12 | - |
| 12 |
|
Go to Step 2 | System OK |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.