SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 918 (BATTERY, CHARGING SYSTEM AND STARTING SYSTEM)REPAIR INSTRUCTIONSSTARTER MOTOR REPLACEMENTREMOVAL PROCEDURE
2006 Chevrolet Suburban C2500, 6.0 U

Removal Procedure

2006 Chevrolet Suburban C2500, 6.0 USECTION Removal Procedure
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Oil Pan Skid Plate & Bolts
    GM1698082Courtesy of GENERAL MOTORS CORP.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. For 1500 series vehicles, remove the oil pan skid plate bolts and plate, if equipped.
    4. Fig 2: View Of Oil Pan Skid Plate & Bolts
    GM1698083Courtesy of GENERAL MOTORS CORP.
  4. For 2500 series vehicles, remove the front 2 oil pan skid plate bolts, loosen the rear 2 bolts and remove the skid plate, if equipped.
    5. Fig 3: View Of Transmission Cover Bolt
    GM663487Courtesy of GENERAL MOTORS CORP.
  5. Remove the transmission cover bolt.
    6. Fig 4: View Of Starter & Bolts (4.8L, 5.3L & 6.0L)
    GM663527Courtesy of GENERAL MOTORS CORP.
  6. Remove the starter bolts.
    7. Fig 5: View Of Engine Wiring Harness Electrical Connector & Components
    GM1698087Courtesy of GENERAL MOTORS CORP.
  7. Disconnect the engine wiring harness electrical connector (4) from the oil level sensor.
  8. Slide the starter forward until the starter clears the transmission.
  9. Lower the vehicle half way.
  10. Remove the right front wheel and tire. Refer to Tire and Wheel Removal and Installation .
    11. Fig 6: View Of Engine Wiring Harness Lead Terminal & Nut
    GM1699540Courtesy of GENERAL MOTORS CORP.
  11. Remove the engine wiring harness lead nut (1).
  12. Remove the engine wiring harness lead terminal (2) from the starter.
    13. Fig 7: View Of Starter Solenoid Cable Clip & Bolt
    GM1702990Courtesy of GENERAL MOTORS CORP.
  13. Remove the starter solenoid cable clip bolt (2) from the frame.
    14. Fig 8: View Of Starter Solenoid Cable & Nut
    GM1699544Courtesy of GENERAL MOTORS CORP.
  14. Remove the starter solenoid cable nut (1).
  15. Remove the starter solenoid cable (2) from the starter.
  16. Remove the starter out through the wheel well opening.
    17. Fig 9: View Of Transmission Cover & Starter
    GM663489Courtesy of GENERAL MOTORS CORP.
  17. If replacing the starter, unsnap the transmission cover from the starter.
    18. Fig 10: View Of Starter & Heat Shield
    GM663472Courtesy of GENERAL MOTORS CORP.
  18. If replacing the starter, remove the starter heat shield.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.