SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1340 (ANTI-LOCK BRAKE SYSTEM - HYBRID)DIAGNOSTIC INFORMATION & PROCEDURESDTC C0455CIRCUIT/SYSTEM TESTING
2006 Chevrolet Suburban C2500, 6.0 U

Circuit/System Testing

2006 Chevrolet Suburban C2500, 6.0 USECTION Circuit/System Testing
WARNING: This page is about a different car, the 2008 GMC Yukon and 2008 Chevrolet Tahoe. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the harness connector at the steering angle sensor.
  2. Ignition OFF, test for less than 5.0 ohm between the low reference circuit terminal 2 and ground.
    • If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
  3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 1 and ground.
    • If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the EBCM.
    • If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the EBCM.
  4. Verify the scan tool Steering Wheel Sensor Signal parameter is less than 1 volt.
    • If greater than the specified range, test the signal circuit terminal 6 for a short to voltage. If the circuit tests normal, replace the EBCM.
  5. Install a 3A fused jumper wire between the signal circuit terminal 6 and the 5-volt reference circuit terminal 1. Verify the scan tool Steering Wheel Sensor Signal parameter is greater than 4.5 volts.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the EBCM.
  6. Verify the scan tool Digital SWPS Phase A parameter is High.
    • If not the specified parameter, test the signal circuit terminal 7 for a short to ground. If the circuit tests normal, replace the EBCM.
  7. Install a 3A fused jumper wire between the signal circuit terminal 3 and the low reference circuit terminal 2. Verify the scan tool Digital SWPS Phase A parameter is Low.
    • If not the specified parameter, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the EBCM.
  8. Verify the scan tool Digital SWPS Phase B parameter is High.
    • If not the specified parameter, test the signal circuit terminal 4 for a short to ground. If the circuit tests normal, replace the EBCM.
  9. Install a 3A fused jumper wire between the signal circuit terminal 4 and the low reference circuit terminal 2. Verify the scan tool Digital SWPS Phase B parameter is Low.
    • If not the specified parameter, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the EBCM.
  10. Ignition ON, test for B+ between the signal circuit terminal 5 and ground.
    • If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the EBCM.
  11. If the circuits test normal, replace the steering angle sensor.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.