SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1079 (FRONT DRIVE AXLE)REPAIR INSTRUCTIONSDIFFERENTIAL CARRIER ASSEMBLY REPLACEMENTREMOVAL PROCEDURE
2006 Chevrolet Suburban C2500, 6.0 U

Removal Procedure

2006 Chevrolet Suburban C2500, 6.0 USECTION Removal Procedure
WARNING: This page is about a different car, the 2007 GMC Sierra and 2007 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
  1. Turn the steering wheel all the way to the left.
  2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Place jack or utility stands at the rear end of the vehicle.
  4. Remove the oil pan shield. Refer to Oil Pan Skid Plate Replacement .
  5. Remove the engine shield, if equipped. Refer to Engine Shield Replacement .
  6. Drain the differential carrier assembly. Refer to Front Axle Lubricant Replacement .
  7. Disconnect the front propeller shaft from the differential carrier assembly. Refer to Front Propeller Shaft Replacement .
  8. Remove the relay rod. Refer to Relay Rod Replacement .
  9. Support the differential carrier assembly with a transmission jack or equivalent.
    10. Fig 1: View Of Wheel Drive Shaft Inboard Flange Bolt - Front Drive Axle
    GM763646Courtesy of GENERAL MOTORS CORP.
  10. Remove the wheel drive shaft inboard flange bolts from the inner axle shaft, both sides.
    11. Fig 2: View Of Front Axle Actuator Electrical Connector
    GM834234Courtesy of GENERAL MOTORS CORP.
  11. Disconnect the electrical connector from the front axle actuator, S4WD axle only.
    12. Fig 3: View Of Wire Harness To Inner Axle Shaft Housing (S4WD)
    GM924830Courtesy of GENERAL MOTORS CORP.
  12. Disconnect the wire harness from the inner axle shaft housing, S4WD axle only.
    13. Fig 4: View Of Wire Harness To Differential Carrier Assembly (S4WD)
    GM924846Courtesy of GENERAL MOTORS CORP.
  13. Disconnect the wire harness from the differential carrier assembly, S4WD axle only.
    14. Fig 5: View Of Vent Hose To Differential Carrier Assembly
    GM834272Courtesy of GENERAL MOTORS CORP.
  14. Disconnect the vent hose from the differential carrier assembly.
    15. Fig 6: View Of Inner Axle Housing Nuts
    GM834241Courtesy of GENERAL MOTORS CORP.
  15. Remove the inner axle housing nuts and washers from the bracket.
    16. Fig 7: View Of Differential Carrier Upper Mounting Bolt
    GM834276Courtesy of GENERAL MOTORS CORP.
  16. Remove the differential carrier assembly upper mounting bolt and the nut.
  17. Pivot the differential carrier assembly forward and down on the lower mount bolt while it is being supported by the transmission jack.
  18. Secure the differential carrier assembly to the jack.
    19. Fig 8: View Of Differential Carrier Lower Mounting Bolt
    GM834278Courtesy of GENERAL MOTORS CORP.
  19. Remove the differential carrier assembly lower mounting bolt and the nut.
  20. Remove the differential carrier assembly.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.