X106 Forward Lamp Harness to Right Headlamp Harness (X88 or Z75 without EXP)

2006 Chevrolet Suburban C1500, 5.3 ZSECTION X106 Forward Lamp Harness to Right Headlamp Harness (X88 or Z75 without EXP)
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
GM646372
GM847234
Connector Part Information
  • Harness Type: Forward Lamp
  • OEM Connector: 15326654
  • Service Connector: 88986254
  • Description: 8-Way F GT 280 Series Sealed (BK)
Connector Part Information
  • Harness Type: Right Headlamp
  • OEM Connector: 15326655
  • Service Connector: 15306424
  • Description: 8-Way M GT 280 Series Sealed (BK)
Terminal Part Information
  • Terminated Lead: Pins A, B, F - 13575405
  • Terminated Lead: Pins C-E - 13327132
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-4A (PU)
  • Terminal/Tray: 15304719/19
  • Core/Insulation Crimp: Pins A, B, F - 2/5
  • Core/Insulation Crimp: Pins C-E - E/5
Terminal Part Information
  • Terminal/Tray: Service by Harness - See Part Catalog
  • Core/Insulation Crimp: Not Available
  • Release Tool/Test Probe: Not Available
X106 Forward Lamp Harness to Right Headlamp Harness (X88 or Z75 without EXP)

Pin Wire Circuit Function Pin Wire Circuit Function
A 0.8 TN/WH 312 Right Headlamp Low Beam Control A 0.35 YE - Right Headlamp Low Beam Control
B 1 BK 250 Ground B 0.35 BK - Ground
C 0.8 L-GN/BK 311 Right Headlamp High Beam Control C 0.35 D-GN/WH - Right Headlamp High Beam Control
D 0.5 D-BU 545 Daytime Running Lamp (DRL) Relay Control D 0.35 L-BU - Daytime Running Lamp (DRL) Relay Control
E 0.5 BN 2609 Right Rear Park Lamps Control E 0.35 BN - Right Rear Park Lamps Control
F 1 BK 150 Ground F 0.35 BK - Ground
G 0.5 D-BU/WH 1315 Right Front Turn Signal Lamp Control (X88) G 0.35 D-BU/WH - Right Front Turn Signal Lamp Control (X88)
H - - Not Used H - - Not Used
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.