X100 Forward Lamp Harness to Left Headlamp Harness (X88 or Z75 without EXP)

2006 Chevrolet Suburban C1500, 5.3 ZSECTION X100 Forward Lamp Harness to Left Headlamp Harness (X88 or Z75 without EXP)
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
GM646372
GM847234
Connector Part Information
  • Harness Type: Forward Lamp
  • OEM Connector: 15326654
  • Service Connector: 88986254
  • Description: 8-Way F GT 280 Series Sealed (BK)
Connector Part Information
  • Harness Type: Left Headlamp
  • OEM Connector: 15326655
  • Service Connector: 15306424
  • Description: 8-Way M GT 280 Series Sealed (BK)
Terminal Part Information
  • Terminated Lead: Pins A, B, F - 13575405
  • Terminated Lead: Pins C-E, G - 13217132
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-4A (PU)
  • Terminal/Tray: 15304719/19
  • Core/Insulation Crimp: Pins A, B, F - 2/5
  • Core/Insulation Crimp: Pins C-E, G - E/5
Terminal Part Information
  • Terminal/Tray: 15304731/19
  • Core/Insulation Crimp: Pins A, B, F: 2/5
  • Core/Insulation Crimp: Pins C-E, G: E/5
  • Release Tool/Test Probe: 15315247/J-35616-5 (PU)
X100 Forward Lamp Harness to Left Headlamp Harness (X88 or Z75 without EXP)

Pin Wire Circuit Function Pin Wire Circuit Function
A 0.8 YE 712 Left Headlamp Low Beam Control A 0.35 YE - Left Headlamp Low Beam Control
B 1 BK 150 Ground B 0.35 BK - Ground
C 0.5 D-GN/WH 711 Left Headlamp High Beam Control C 0.35 D-GN/WH - Left Headlamp High Beam Control
D 0.5 D-BU 545 Daytime Running Lamp (DRL) Relay Control D 0.35 D-BU - Daytime Running Lamp (DRL) Relay Control
E 0.5 BN 2509 Left Rear Park Lamps Control E 0.35 BN - Left Rear Park Lamps Control
F 1 BK 250 Ground F 0.35 BK - Ground
G 0.5 L-BU/WH 1314 Left Front Turn Signal Lamp Control (X88) G 0.35 L-BU/WH - Left Front Turn Signal Lamp Control (X88)
H - - Not Used H - - Not Used
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.