SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C1500, 5.3 ZREPAIR AND DIAGNOSISBRAKESANTILOCK BRAKE SYSTEM WITH TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESDTC C0283 (W/JL4)TEST DESCRIPTION
2006 Chevrolet Suburban C1500, 5.3 Z

Test Description

2006 Chevrolet Suburban C1500, 5.3 ZSECTION Test Description

The number below refers to the step number on the diagnostic table.

  1. 4:  This step tests the traction control switch circuitry. If the fuse opens when you perform this test, the traction control switch signal circuit is shorted to ground.
DTC C0283 (W/JL4)

Step Action Yes No
Schematic Reference: ABS Schematics 
Connector End View Reference: ABS Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Use a scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 5 seconds.
  3. Turn ON the ignition for up to 20 seconds.
Does the DTC set?		 Go to Step 3  Go to Diagnostic Aids
3
  1. Turn OFF the ignition.
  2. Disconnect the traction control switch harness connector. Refer to Traction Control Switch Replacement (Stabilitrak) .
  3. Turn ON the ignition.
  4. Connect a test lamp between the ignition 3 voltage circuit and a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 8 
4 
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition.
  3. Connect a fused jumper wire between the ignition 3 voltage circuit and the traction control switch signal circuit at the traction control switch harness connector.
  4. Turn ON the ignition for up to 20 seconds.
Does the DTC set?		 Go to Step 5  Go to Step 9 
5 Test the traction control switch signal circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 11  Go to Step 6 
6 Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 11  Go to Step 7 
7 Replace the EBCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 11  -
8 Repair the open in the ignition 3 voltage circuit. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?		 Go to Step 11  -
9 Inspect for poor connections at the harness connector of the traction control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 11  Go to Step 10 
10 Replace the traction control switch. Refer to Traction Control Switch Replacement (Stabilitrak) .
Did you complete the replacement?		 Go to Step 11  -
11
  1. Use the scan tool to clear the DTCs.
  2. Turn OFF the ignition for 5 seconds.
  3. Turn ON the ignition.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.
Does the DTC reset?		 Go to Step 3  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.