SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006SSR AUTOMATICREPAIR AND DIAGNOSISELECTRICALINSTRUMENT PANEL SYSTEM DISPLAYS, GAUGES AND CONSOLEDIAGNOSTIC INFORMATION AND PROCEDURESDTC P0462TEST DESCRIPTION
2006 Chevrolet SSR Automatic

Test Description

2006 Chevrolet SSR AutomaticSECTION Test Description

The number below refers to the step number on the diagnostic table.

  1. 3:  Tests for the proper operation of the circuit in the high voltage range.
DTC P0462

Step Action Value(s) Yes No
Schematic Reference: Instrument Cluster Schematics 
Connector End View Reference: Master Electrical Component List in Wiring Systems
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Fuel Tank Level Remaining parameter in the powertrain control module (PCM) Enhanced evaporative emission (EVAP) data list.
Does the scan tool indicate that the Fuel Tank Level Remaining parameter is less than the specified value?		 4% Go to Step 3  Go to Diagnostic Aids
3 
  1. Turn OFF the ignition.
  2. Disconnect C105.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Fuel Tank Level Remaining parameter.
Does the scan tool indicate that the Fuel Tank Level Remaining parameter is greater than the specified value?		 98% Go to Step 5  Go to Step 4 
4 Test the signal circuit of the fuel level sender for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 10  Go to Step 7 
5 Test the signal circuit of the fuel level sender for a short to ground between C105 and the fuel level sender. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 10  Go to Step 6 
6 Inspect for poor connections at the harness connector of the fuel level sender. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 10  Go to Step 8 
7 Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 10  Go to Step 9 
8 Replace the fuel level sender. Refer to Fuel Sender Assembly Replacement in Engine Controls - 6.0L.
Did you complete the replacement?		 - Go to Step 10  -
9 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 10  -
10
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.