Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 864 (ENGINE MECHANICAL - 2.2L)COMPONENT LOCATORDISASSEMBLED VIEWS
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Disassembled Views
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Disassembled Views
WARNING: This page is about a different car, the 2010 Pontiac G5 and 2010 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 201 | Exhaust Valve |
| 202 | Intake Valve |
| 203 | Timing Chain Guide Bolt Access Hole |
| 204 | Cylinder Head |
| 205 | Cylinder Head Gallery Plug |
| 206 | Hydraulic Lash Adjuster |
| 207 | Roller Finger Follower |
| 208 | Cylinder Head Bolt |
| 209 | Small Cylinder Head Bolt |
| 210 | Valve Stem Seal |
| 211 | Valve Spring |
| 212 | Valve Spring Retainer |
| 213 | Valve Keys |
| 214 | Hydraulic Lash Adjuster |
| 215 | Roller Finger Follower |
| 216 | lntake Camshaft |
| 219 | Camshaft Cap |
| 220 | Exhaust Camshaft |
| 221 | Camshaft Cap |
| 222 | Camshaft Cap Bolt |
| 300 | Coolant Air Bleed Fitting |
| 413 | Engine Oil Fill Cap |
| 507 | Fuel Injector Rotator Cup |
| 508 | Fuel Injector O-ring |
| 509 | Fuel Injector |
| 510 | Fuel Injector O-ring |
| 511 | Fuel Injector Clip |
| 512 | Fuel Rail |
| 513 | Camshaft Cover Gasket |
| 514 | Camshaft Cover |
| 515 | Camshaft Cover Bolt |
| 707 | Front Lift Bracket Bolt |
| 708 | Front Lift Bracket |
| 709 | Rear Lift Bracket |
| 710 | Rear Lift Bracket Bolt |
| 713 | Fuel Injector Wiring Harness |
| 717 | Spark Plug |
| 718 | Camshaft Position Actuator Solenoid Valve - Exhaust |
| 719 | Camshaft Position Actuator Solenoid Valve - Intake |
| 720 | Camshaft Position Actuator Solenoid Valve Bolt |
| 721 | Ignition Coil |
| 724 | Ignition Coil Bolt |
| 725 | Camshaft Position Sensor |
| 726 | Camshaft Position Sensor Bolt |
| 727 | Camshaft Position Sensor |
| 728 | Camshaft Position Sensor Bolt |
| Callout | Component Name |
|---|---|
| 408 | Oil Indicator Tube O-ring |
| 409 | Oil Indicator Tube |
| 410 | Oil Indicator Tube Bolt |
| 411 | Oil Indicator O-ring |
| 412 | Oil Indicator |
| 500 | Intake Manifold Gasket |
| 501 | Intake Manifold Bolt |
| 502 | Intake Manifold |
| 503 | Throttle Body Seal |
| 504 | Throttle Body |
| 506 | Throttle Body Bolt |
| 711 | Map Sensor |
| Callout | Component Name |
|---|---|
| 1 | Exhaust Manifold Heat Shield Bolt |
| 2 | Exhaust Manifold Heat Shield |
| 3 | Exhaust Manifold Heat Shield Bolt |
| 4 | Secondary Air Injection Assembly Nut |
| 5 | Secondary Air Injection Assembly |
| 6 | Secondary Air Injection Check Stud |
| 7 | Secondary Air Injection Bolt |
| 8 | Secondary Air Injection Pipe Assembly |
| 9 | Secondary Air Injection Stud |
| 10 | Secondary Air Injection Check Valve Gasket |
| 11 | Secondary Air Injection Bolt |
| 12 | Exhaust Manifold Gasket |
| 13 | Exhaust Manifold Stud |
| 14 | Exhaust Manifold |
| 15 | Exhaust Manifold Nut |
| 16 | Oxygen Sensor |
| 17 | Exhaust Manifold Brace Bolt |
| 18 | Exhaust Manifold Brace |
| 19 | Exhaust Manifold Brace Bolt |
| Callout | Component Name |
|---|---|
| 1 | Water Pump to Engine Block Seal |
| 2 | Water Pump |
| 3 | Water Transfer Pipe O-ring Seals |
| 4 | Water Transfer Pipe |
| 5 | Coolant Temperature Sensor |
| 6 | Thermostat Housing to Block Gasket |
| 7 | Thermostat Housing |
| 8 | Thermostat |
| 9 | Thermostat Gasket |
| 10 | Thermostat Housing Cap Bolt |
| 11 | Thermostat Housing Cap |
| 12 | Water Pipe Support Bracket |
| 13 | Water Pipe Support Bracket Bolt |
| 14 | Water Pipe Support Bracket Bolt Stud |
| 15 | Cylinder Head Gasket |
| 16 | Piston Ring Assembly |
| 17 | Piston Assembly |
| 18 | Connecting Rod |
| 19 | Connecting Rod Cap Bolt |
| 20 | Connecting Rod Bearing |
| 21 | Oil Filter Cap |
| 22 | Oil Filter Cap O-ring |
| 23 | Cylinder Head Alignment Pin |
| 24 | Oil Filter |
| 25 | Engine Block Gallery Plug |
| 26 | Engine Block to Transaxle Alignment Pin |
| 27 | Crankshaft Position Sensor |
| 28 | Crankshaft Position Sensor Bolt |
| 29 | Oil Pressure Switch |
| 30 | Knock Sensor |
| 31 | Crankshaft Bearing - Upper |
| 32 | Crankshaft Rear Seal |
| 33 | Flywheel - Automatic Transmission |
| 34 | Manual Transaxle Flywheel |
| 35 | Manual Transaxle Flywheel Bolt |
| 36 | Automatic Transaxle Flywheel to Crankshaft Bolt |
| 37 | Crankshaft |
| 38 | Crankshaft Bearing - Lower |
| 39 | Lower Crankcase |
| 40 | Engine Oil Pan Alignment Pins |
| 41 | Lower Crankcase Perimeter Bolt |
| 42 | Engine Oil Pan |
| 43 | Air Pump Assembly |
| 44 | Air Pump Assembly Bolt |
| 45 | Air Pump Assembly Bolt |
| 46 | Engine Oil Pan Long Bolt |
| 47 | Engine Oil Pan Bolt |
| 48 | Engine Oil Pan Drain Plug |
| 49 | Lower Crankcase Main Bearing Bolt |
| 50 | Crankshaft Thrust Bearing - Lower |
| 51 | Crankshaft Thrust Bearing - Upper |
| 52 | Piston Oil Nozzle Assembly |
| 53 | Engine Block |
| 54 | Cylinder Bore Sleeve |
| Callout | Component Name |
|---|---|
| 123 | Balance Shaft Rear Bearing |
| 124 | Exhaust Balance Shaft |
| 125 | Intake Balance Shaft |
| 126 | Exhaust Balance Shaft Bearing Carrier |
| 127 | Intake Balance Shaft Bearing Carrier |
| 128 | Exhaust Balance Shaft Drive Sprocket |
| 129 | Intake Balance Shaft Drive Sprocket |
| 130 | Balance Shaft Drive Sprocket Bolts |
| 223 | Upper Timing Chain Guide Bolt |
| 224 | Upper Timing Chain Guide |
| 225 | Exhaust Camshaft Position Actuator |
| 226 | Intake Camshaft Position Actuator |
| 227 | Camshaft Position Actuator Bolt |
| 228 | Timing Chain Oil Nozzle |
| 229 | Timing Chain Oil Nozzle Bolt |
| 230 | Timing Chain Drive Sprocket |
| 231 | Fixed Timing Chain Guide |
| 232 | Fixed Timing Chain Guide Bolt |
| 233 | Timing Chain |
| 234 | Timing Chain Tensioner Washer |
| 235 | Timing Chain Tensioner Body |
| 236 | Timing Chain Tensioner O-ring Seal |
| 237 | Timing Chain Tensioner Plunger |
| 238 | Adjustable Timing Chain Guide |
| 239 | Adjustable Timing Chain Guide Bolt |
| 240 | Balance Shaft Drive Sprocket |
| 241 | Balance Shaft Drive Chain Guide |
| 242 | Balance Shaft Drive Chain Guide Bolt |
| 243 | Balance Shaft Drive Chain Guide |
| 244 | Balance Shaft Drive Chain Guide Bolt |
| 245 | Balance Shaft Drive Chain |
| 246 | Balance Shaft Drive Chain Tensioner Assembly |
| 247 | Balance Shaft Drive Chain Tensioner Assembly Bolt |
| 248 | Adjustable Balance Shaft Drive Chain Guide |
| 249 | Adjustable Balance Shaft Drive Chain Guide Bolt |
| 314 | Water Pump Drive Sprocket |
| 315 | Water Pump Drive Sprocket Bolt |
| 316 | Water Pump Bolt |
| 317 | Engine Front Cover Access Plate Gasket |
| 318 | Engine Front Cover Access Plate |
| 319 | Engine Front Cover Access Plate Bolt |
| 414 | Engine Front Cover Alignment Pins |
| 415 | Engine Front Cover Gasket |
| 416 | Oil Pump Cover Bolt |
| 417 | Oil Pump Cover |
| 418 | Oil Pump Outer Gerotor |
| 419 | Oil Pump Inner Gerotor |
| 420 | Engine Front Cover |
| 421 | Engine Front Cover Bolt |
| 422 | Oil Pressure Relief Valve Spring |
| 423 | Oil Pressure Relief Valve Plunger |
| 424 | Oil Pressure Relief Valve O-ring Seal |
| 425 | Oil Pressure Relief Valve Plug |
| 426 | Crankshaft Front Seal |
| 427 | Crankshaft Damper |
| 428 | Crankshaft Damper Bolt |
| 429 | Friction Washer, some models |
| 704 | Belt Tensioner |
| 705 | Belt Tensioner Bolt |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.