SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 663 (ENGINE MECHANICAL - 2.2L (L61))SPECIFICATIONSENGINE MECHANICAL SPECIFICATIONS
2006 Chevrolet Cobalt SS, 4D Sedan, Standard

Engine Mechanical Specifications

2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Engine Mechanical Specifications
WARNING: This page is about a different car, the 2008 Pontiac G5 and 2008 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
Engine Mechanical Specifications

Application Specification
Metric English
General Data
  • Engine Type
 Inline 4 Cylinder
  • Displacement
 2.2 L 134 CID
  • RPO
 L61
  • Liter (VIN)
 F
  • Bore
 85.992-86.008 mm 3.3855-3.3861 in
  • Stroke
 94.6 mm 3.727 in
  • Compression Ratio
 10.0:1
Balance Shaft
  • Bearing Clearance
 0.030-0.060 mm 0.0012-0.0024 in
  • Bearing Diameter - Inside - Carrier
 20.050-20.063 mm 0.7894-0.7899 in
  • Bearing Diameter - Outside - Carrier
 41.975-41.995 mm 1.6526-1.6534 in
  • Bearing Journal Diameter
 20.000-20.020 mm 0.7874-0.7882 in
  • Bushing Clearance
 0.033-0.102 mm 0.0013-0.0040 in
  • Bushing Diameter - Inside
 36.776-36.825 mm 1.4479-1.4498 in
  • Bushing Journal Diameter
 36.723-36.743 mm 1.4458-1.4466 in
  • End Play
 0.050-0.300 mm 0.0020-0.0118 in
Block
  • Balance Shaft Bearing Bore Diameter - Carrier
 42.000-42.016 mm 1.6535-1.6542 in
  • Balance Shaft Bushing Bore Diameter
 40.763-40.776 mm 1.6048-1.6054 in
  • Crankshaft Main Bearing Bore Diameter
 64.068-64.082 mm 2.5224-2.5229 in
  • Cylinder Bore Diameter
 85.992-86.008 mm 3.3855-3.3861 in
  • Cylinder Bore Out-of-Round - Maximum
 0.010 mm 0.0004 in
  • Cylinder Bore Taper - Maximum
 0.010 mm 0.0004 in
  • Cylinder Head Deck Surface Flatness - Transverse
 0.030 mm 0.0012 in
  • Cylinder Head Deck Surface Flatness - Longitude
 0.050 mm 0.002 in
  • Cylinder Head Deck Surface Flatness - Overall
 0.08 mm 0.0031 in
Camshaft
  • Camshaft End Play
 0.040-0.144 mm 0.0016-0.0057 in
  • Camshaft Journal Diameter
 26.935-26.960 mm 1.0604-1.0614 in
  • Camshaft Thrust Surface
 21.000-21.052 mm 0.8268-0.8252 in
Connecting Rod
  • Connecting Rod Bearing Clearance
 0.029-0.073 mm 0.0011-0.0029 in
  • Connecting Rod Bore Diameter - Bearing End
 52.118-52.134 mm 2.0519-2.05252 in
  • Connecting Rod Bore Diameter - Pin End
 20.007-20.021 mm 0.7877-0.7882 in
  • Connecting Rod Side Clearance
 0.070-0.370 mm 0.0028-0.0146 in
  • Connecting Rod Straightness - Bend - Maximum
 0.021 mm 0.0083 in
  • Connecting Rod Straightness - Twist - Maximum
 0.04 mm 0.0157 in
Crankshaft
  • Connecting Rod Journal Diameter
 49.000-49.014 mm 1.9291-1.9297 in
  • Crankshaft End Play
 0.050-0.380 mm 0.0012-0.0150 in
  • Crankshaft Main Bearing Clearance
 0.031-0.067 mm 0.0012-0.0026 in
  • Crankshaft Main Journal Diameter
 55.994-56.008 mm 2.2045-2.2050 in
Cylinder Head
  • Surface Flatness - Block Deck - Transverse
 0.030 mm 0.0012 in
  • Surface Flatness - Block Deck - Longitude
 0.050 mm 0.002 in
  • Surface Flatness - Block Deck - Overall
 0.1 mm 0.004 in
  • Valve Guide Bore - Exhaust
 6.000-6.012 mm 0.2362-0.2367 in
  • Valve Guide Bore - Intake
 6.000-6.012 mm 0.2362-0.2367 in
  • Valve Lifter Bore Diameter - Stationary Lash Adjusters
 12.013-12.037 mm 0.4730-0.4739 in
Lubrication System
  • Oil Pressure - Minimum - @1000 RPM
 344.75-551.60 kPa 50-80 psi
  • Oil Capacity
 4.8L 5.0 quarts
Piston Rings
  • Piston Ring End Gap - First Compression Ring
 0.20-0.40 mm 0.008-0.016 in
  • Piston Ring End Gap - Second Compression Ring
 0.35-0.55 mm 0.014-0.022 in
  • Piston Ring End Gap - Oil Control Ring - Rails
 0.25-0.76 mm 0.010-0.030 in
  • Piston Ring to Groove Clearance - First Compression Ring
 0.04-0.08 mm 0.0015-0.0031 in
  • Piston Ring to Groove Clearance - Second Compression Ring
 0.030-0.069 mm 0.0012-0.0027 in
  • Piston Ring to Groove Clearance - Oil Control Ring
 0.043-0.192 mm 0.0017-0.0076 in
  • Piston Ring Thickness - First Compression Ring
 1.170-1.190 mm 0.0461-0.0469 in
  • Piston Ring Thickness - Second Compression Ring
 1.471-1.490 mm 0.0579-0.0587 in
  • Piston Ring Thickness - Oil Control Ring - Rail - Maximum
 0.43 mm 0.0169 in
  • Piston Ring Thickness - Oil Control Ring - Spacer
 1.574-1.651 mm 0.0620-0.0650 in
Pistons and Pins
  • Pin - Piston Pin Clearance to Connecting Rod Bore
 0.007-0.026 mm 0.0003-0.0010 in
  • Pin - Piston Pin Clearance to Piston Pin Bore
 0.002-0.012 mm 0.0001-0.0005 in
  • Pin - Piston Pin Diameter
 19.995-20.000 mm 0.7872-0.7874 in
  • Pin - Piston Pin End Play
 0.210-1.266 mm 0.0083-0.0498 in
  • Piston - Piston Diameter - @14.5 mm up
 85.967-85.982 mm 3.3845-3.3851 in
  • Piston - Piston Pin Bore Diameter
 20.002-20.007 mm 0.07875-0.7877 in
  • Piston - Piston Ring Groove Width - Top
 1.23-1.25 mm 0.0484-0.0492 in
  • Piston - Piston Ring Groove Width - Second
 1.52-1.54 mm 0.0598-0.0606 in
  • Piston - Piston Ring Groove Width - Oil Control
 2.52-2.54 mm 0.0992-0.1000 in
  • Piston - Piston To Bore Clearance
 0.010-0.041 mm 0.0004-0.0016 in
Valve System
  • Valve Lifters - Valve Lifter Diameter - Stationary Lash Adjuster
 11.986-12.000 mm 0.0005-0.0020 in
  • Valve Lifters - Valve Lifter-to-Bore Clearance - Stationary Lash Adjuster
 0.013-0.051 mm 3.2210-3.2299 in
  • Valve Springs - Valve Spring Load - Closed - @32.5 mm
 245.0-271.0 N. - Eng Spec.
  • Valve Springs - Valve Spring Load - Open - @22.5 mm
 525.0-575.0 N. - Eng Spec.
  • Valves - Valve Face Runout - Maximum
 0.04 mm 0.0016 in
  • Valves - Valve Seat Runout - Maximum
 0.05 mm 0.0020 in
  • Valves - Valve Stem Diameter - Intake
 5.955-5.970 mm 0.2344-0.2355 in
  • Valves - Valve Stem Diameter - Exhaust
 5.935-5.950 mm 0.2337-0.2343 in
  • Valves - Valve Stem to Guide Clearance - Intake
 0.030-0.057 mm 0.0012-0.0022 in
  • Valves - Valve Stem to Guide Clearance - Exhaust
 0.050-0.077 mm 0.0020-0.0026 in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.