Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 601 (CRUISE CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Scan Tool Data List
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Scan Tool Data List
WARNING: This page is about a different car, the 2007 Pontiac G5 Pursuit, 2007 Pontiac G5, and 2007 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
The scan tool data lists contain all of the cruise control related parameters that are available on the scan tool. The parameters in the list are arranged in alphabetical order. The data list column indicates the location of the parameter within the scan tool menu selections.
Use the scan tool data lists as directed by a diagnostic table or in order to supplement the diagnostic procedures. Begin all of the diagnostic procedures with DIAGNOSTIC SYSTEM CHECK - VEHICLE .
Use the scan tool data lists only after the following is determined:
- There is no published DTC procedure nor published symptom procedure for the customer concern.
- The DTC or symptom procedure indicated by the diagnostic system check does not resolve the customer concern.
The typical data values are obtained from a properly operating vehicle under the conditions specified in the first row of the scan tool data list table. Comparison of the parameter values from the suspect vehicle with the typical data values may reveal the source of the customer concern.
Body and Accessories - 2.0L
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature/Vehicle is in Park or Neutral/Cruise On/Off Switch is Turned Off | |||
| Battery Voltage Signal | BCM Data | Volts | Varies |
| Clutch Pedal Switch | PCM Data | Applied/Released | Released |
| CPP Switch (If Equipped) | PCM Data | Applied/Released | Released |
| Cruise Control Switch | BCM Data | Off/On/Error/Resume/Set | Off |
| Cruise Control Switch | BCM Data | Volts | 0 Volts |
| Engine Speed | PCM Data | RPM | Varies |
| Ignition 1 Signal | PCM Data | Volts | Varies |
| Stop Lamp Pedal Switch | PCM Data | Applied/Released | Released |
Body and Accessories - 2.2L and 2.4L
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature/Vehicle is in Park or Neutral/Cruise On/Off Switch is Turned Off | |||
| Battery Voltage Signal | BCM Data | Volts | Varies |
| Cruise Cancel Switch (2.4L) | ECM Data | Active/Inactive/Invalid | Inactive |
| Cruise Control Active | ECM Data | No/Yes | No |
| Cruise Control Switch | BCM Data | Off/On/Error/Resume/Set | Off |
| Cruise Control Switch | BCM Data | Volts | 0 Volts |
| Cruise Disengage 1-8 History | ECM Data | The last reason for cruise control disengagement | Varies |
| Cruise On/Off Switch | ECM Data | On/Off | Off |
| Cruise Resume/Accel Switch (2.2L) | ECM Data | On/Off | Off |
| Cruise Resume/Accel Switch (2.4L) | ECM Data | Active/Inactive/Invalid | Off |
| Cruise Set Switch (2.4L) | ECM Data | Active/Inactive/Invalid | Inactive |
| Cruise Set/Coast Switch (2.2L) | ECM Data | Active/Inactive/Invalid | Inactive |
| Engine Speed | ECM Data | RPM | Varies |
| Ignition 1 Signal | ECM Data | Volts | Varies |
| Stop Lamp Pedal Switch | ECM Data | Applied/Released | Released |
| TCC/Cruise Brake Pedal Switch | ECM Data | Applied/Released | Released |
| Vehicle Speed Sensor | ECM Data | km/h (mph) | 0 km/h (0 mph) |
Engine - 2.0L
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature/Vehicle is in Park or Neutral/Cruise On/Off Switch is Turned Off | |||
| Clutch Pedal Switch | Cruise Control Data | Applied/Released | Released |
| Cruise Control Active | Cruise Control Data | Yes/No | No |
| Cruise Disengage (1-8) History | Cruise Control Data | Last reason for cruise control disengagement | Varies |
| Cruise On/Off Switch | Cruise Control Data | On/Off | Off |
| Cruise Resume/Accel. Switch | Cruise Control Data | On/Off | Off |
| Cruise Set/Coast Switch | Cruise Control Data | On/Off | Off |
| Initial Brake Apply Signal | Cruise Control Data | Applied/Released | Released |
| Engine Speed | Cruise Control Data | RPM | Varies |
| Ignition 1 Signal | Cruise Control Data | Volts | Varies |
| Reduced Engine Power | TAC Data | Active/Inactive | Inactive |
| Stoplamp Pedal Switch | Cruise Control Data | Applied/Released | Released |
| Traction Control Status | Cruise Control Data | Active/Inactive | Inactive |
| Vehicle Speed Sensor | Cruise Control Data | km/h (mph) | 0 |
Engine - 2.2L
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature/Vehicle is in Park or Neutral/Cruise On/Off Switch is Turned Off | |||
| Cruise Control Active | Cruise Control Data | Yes/No | No |
| Cruise Disengage (1-8) History | Cruise Control Data | Last reason for cruise control disengagement | Varies |
| Cruise On/Off Switch | Cruise Control Data | On/Off | Off |
| Cruise Resume/Accel. Switch | Cruise Control Data | On/Off | Off |
| Cruise Set/Coast Switch | Cruise Control Data | Active/Inactive/Invalid | Inactive |
| Initial Brake Apply Signal | Cruise Control Data | Applied/Released | Released |
| Engine Speed | Cruise Control Data | RPM | Varies |
| Ignition 1 Signal | Cruise Control Data | Volts | Varies |
| Reduced Engine Power | TAC Data | Active/Inactive | Inactive |
| Stoplamp Pedal Switch | Cruise Control Data | Applied/Released | Released |
| TCC/Cruise Brake Pedal Switch | Cruise Control Data | Applied/Released | Released |
| Traction Control Status | TAC Data | Active/Inactive | Inactive |
| Vehicle Speed Sensor | Cruise Control Data | km/h (mph) | 0 |
Engine - 2.4L
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature/Vehicle is in Park or Neutral/Cruise On/Off Switch is Turned Off | |||
| CPP Switch (If Equipped) | TAC Data | Applied/Released | Released |
| Cruise Control Active | TAC Data | Yes/No | No |
| Engine Speed | TAC Data | RPM | Varies |
| Ignition 1 Signal | TAC Data | Volts | Varies |
| Reduced Engine Power | TAC Data | Active/Inactive | Inactive |
| TCC/Cruise Brake Pedal Switch | TAC Data | Applied/Released | Released |
| Vehicle Speed Sensor | TAC Data | km/h (mph) | 0 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.