Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 398 (COMPUTER/INTEGRATING SYSTEMS)DIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Scan Tool Data List
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Scan Tool Data List
WARNING: This page is about a different car, the 2006 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
Accessory
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| A/C Sensor | Volts | Varies |
| Afterblow Relay Cmd. | On/Off | Off |
| Afterblow Relay Fdbk. | High/Low | Low |
| Battery 1 | Volts | Varies |
| Coolant Gauge Position | % of Gauge | % |
| Fuel Gauge Position | % of Full | % |
| Odometer | km/miles | Varies |
| Rear Defog Relay Cmd. | On/Off | Off |
| Rear Defog Relay Fdbk. | High/Low | High |
| Rear Defog Switch | On/Off | Off |
| Shifter Unlock Cmd. | On/Off | On |
| Shifter Unlock Fdbk. | High/Low | Low |
Switch Inputs
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| A/C Request (Manual A/C) | Yes/No | No |
| Battery 1 | Volts | Varies |
| Driver Door Switch | High/Low | High |
| Fog Lamp Switch | On/Off | Off |
| Front Wiper Delay Switch | On/Off | Off |
| High Beam Switch | On/Off | On |
| Key In Ignition | Yes/No | Yes |
| Liftgate Ajar Switch | High/Low | High |
| Lock Switch | On/Off | Off |
| Low Beam Input = DRL | Yes/No | No |
| Low Beam Input = High | Yes/No | No |
| Low Beam Input = Off | Yes/No | Yes |
| Low Brake Fluid | Yes/No | No |
| Low Coolant | Yes/No | No |
| Oil Life Reset Switch | High/Low | High |
| Park Brake Switch | On/Off | On |
| Park Lamp Switch | On/Off | Off |
| Psgr. Door Switches | High/Low | High |
| Rear Defog Switch | On/Off | Off |
| Rear Wiper Switch | On/Off | Off |
| Unlock Switch | On/Off | Off |
Exterior Lamps
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| Battery 1 | Volts | Varies |
| DRL Relay Cmd. | On/Off | Off |
| DRL Relay Fdbk. | High/Low | High |
| Fog Lamp Relay Cmd. | On/Off | Off |
| Fog Lamp Relay Fdbk. | High/Low | High |
| Fog Lamp Switch | On/Off | Off |
| High Beam Switch | On/Off | On |
| Low Beam Input | Volts | Varies |
| Low Beam Input = DRL | Yes/No | No |
| Low Beam Input = High | Yes/No | No |
| Low Beam Input = Off | Yes/No | Yes |
| Park Lamp Switch | On/Off | Off |
Interior Lamps
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| Battery 1 | Volts | Varies |
| Dome Lamp Cmd. | On/Off | Off |
| Dome Lamp Fdbk. | High/Low | High |
| Driver Door Switch | High/Low | High |
| Inadvertent Power Cmd. | On/Off | On |
| Inadvertent Power Fdbk. | High/Low | High |
| I/P Dimmer Input | Volts | Varies |
| I/P Dimmer Output | % Duty Cycle | % |
| Key In Ignition | Yes/No | Yes |
| Psgr. Door Switches | High/Low | High |
Door Locks
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| Battery 1 | Volts | Varies |
| Driver Unlock Relay Cmd. | On/Off | Off |
| Driver Unlock Relay Fdbk. | High/Low | Low |
| Lock All Relay Cmd. | On/Off | Off |
| Lock All Relay Fdbk. | High/Low | Low |
| Lock Switch | On/Off | Off |
| Psgr. Unlock Relay Cmd. | On/Off | Off |
| Psgr. Unlock Relay Fdbk. | High/Low | Low |
| Remote Lock Cmd. | Yes/No | No |
| Remote Panic Cmd. | Yes/No | No |
| Remote Unlock Cmd. | Yes/No | No |
| Unlock Switch | On/Off | Off |
Wiper/Washer
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| Battery 1 | Volts | Varies |
| Front Washer Motor Input | On/Off | Off |
| Front Wiper Delay Relay Cmd. | On/Off | Off |
| Front Wiper Delay Relay Fdbk. | High/Low | High |
| Front Wiper Delay Switch | On/Off | Off |
| Rear Washer Motor Input | On/Off | Off |
| Rear Wiper Relay Cmd. | On/Off | Off |
| Rear Wiper Relay Fdbk. | High/Low | High |
| Rear Wiper Switch | On/Off | Off |
| Wiper Delay 1 | Yes/No | Varies |
| Wiper Delay 2 | Yes/No | Varies |
| Wiper Delay 3 | Yes/No | Varies |
| Wiper Delay Input | Volts | Varies |
Security Data
| Scan Tool Parameter | Units Displayed | Typical Data Value |
|---|---|---|
| Operating Conditions: Ignition in RUN, Engine OFF, All Doors Closed, Park Brake Applied (DRLs OFF) | ||
| Auto-Learn Timer | Seconds | Varies |
| Battery 1 | Volts | Varies |
| Horn Relay Cmd. | On/Off | Off |
| Horn Relay Fdbk. | High/Low | High |
| Ignition 1 Input | High/Low | High |
| Ignition 2 Input | High/Low | High |
| Key Learned | Yes/No | No |
| Key Learn Enabled | Yes/No | Yes |
| Passlock Input | Volts | Varies |
| Passlock Power Fdbk. | High/Low | High |
| Passlock Timer | Seconds | Varies |
| Security LED | On/Off/Flash | Off |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.