SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 375 (DISC BRAKE SYSTEM)SPECIFICATIONSDISC BRAKE COMPONENT SPECIFICATIONS
2006 Chevrolet Cobalt SS, 4D Sedan, Standard

Disc Brake Component Specifications

2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Disc Brake Component Specifications
WARNING: This page is about a different car, the 2006 Chevrolet Monte Carlo and 2006 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
Disc Brake Component Specifications

Application Specification
Metric English
Front Brake Pads (16 in and 17 in)
  • Taper
 0.15 mm 0.006 in
Front Brake Rotor (16 in)
  • Rotor Diameter
 303 mm 11.93 in
  • Rotor Discard Thickness
 28.6 mm 1.126 in
  • Rotor Maximum Allowable Assembled Lateral Runout
 0.06 mm 0.002 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Thickness Variation
 0.025 mm 0.001 in
  • Rotor Minimum Allowable Thickness after Refinishing
 XX mm XX in
  • Rotor Thickness (New)
 30 mm 1.181 in
Front Brake Rotors (17 in)
  • Rotor Diameter
 323 mm 12.72 in
  • Rotor Discard Thickness
 28.6 mm 1.126 in
  • Rotor Maximum Allowable Assembled Lateral Runout
 0.06 mm 0.002 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Thickness Variation
 0.025 mm 0.001 in
  • Rotor Minimum Allowable Thickness after Refinishing
 29.6 mm 1.165 in
  • Rotor Thickness (New)
 30 mm 1.181 in
Rear Brake Pads
  • Taper
 0.15 mm 0.006 in
Rear Brake Rotor
  • Rotor Diameter
 292 mm 11.50 in
  • Rotor Discard Thickness
 9.0 mm 0.354 in
  • Rotor Maximum Allowable Assembled Lateral Runout
 0.06 mm 0.002 in
  • Rotor Maximum Allowable Scoring
 1.50 mm 0.059 in
  • Rotor Maximum Thickness Variation
 0.025 mm 0.001 in
  • Rotor Minimum Allowable Thickness after Refinishing
 9.35 mm 0.368 in
  • Rotor Thickness (New)
 11 mm 0.433 in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.