Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 327 (LIGHTING SYSTEMS)DIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Scan Tool Data List
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Scan Tool Data List
WARNING: This page is about a different car, the 2006 Chevrolet Monte Carlo and 2006 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
Scan Tool Data List
| Scan Tool Parameter | Data Display | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition in the ON position. Bright Light Applied to the DRL ambient light sensor. Park brake not set. Headlamp Switch in the OFF position. I/P lamp switch in the OFF position. Fog lamp switch in the OFF position. | |||
| Ambient Light Sensor | Exterior Lighting | Volts | Volts |
| Ambient Light States | Exterior Lighting | Night/Day Unknown/Invalid | - |
| Auto Hdlp. Disable Sw. | Exterior Lighting | Inactive/Active | - |
| Backup Lamps | Exterior Lighting | On/Off | Off |
| Bass High During Learn | Bass Data | No/Yes | No |
| Bass Learned | Bass Data | No/Yes | Yes |
| Bass Low During Learn | Bass Data | No/Yes | No |
| Bass Moved During Learn | Bass Data | No/Yes | No |
| Bass Valid | Bass Data | No/Yes | Yes |
| Brake Applied Output Signal | Outputs | On/Off | Off |
| Brake Apply Sensor | BCM Data | Volts | 0 volts |
| Brake Lamp | Bass Data | On/Off | Off |
| Center Stop Lamp | Exterior Lighting | On/Off | - |
| Courtesy Lamp PWM Command | Interior Lighting | % | % |
| Courtesy Lamp Active Reason | Interior Lighting | On/Off | Off |
| Current Position | Bass Data | Counts | 0 |
| Dimming Control Reference | Interior Lighting | Volts | Volts |
| Dimming Control Signal | Interior Lighting | % | % |
| Dimming Control Signal | Interior Lighting | Volts | Volts |
| Flash to Pass Switch | Exterior Lighting | Inactive/Active | Inactive |
| Front Fog Lamp Relay | Outputs | On/Off | Off |
| Front Fog Lamp Relay Command | Exterior Lighting | On/Off | Off |
| Front Fog Lamp Switch | Exterior Lighting | Inactive/Active | Inactive |
| Hazard Lamp Switch | Exterior Lighting | Inactive/Active | Inactive |
| Headlamp Switch | Exterior Lighting | Inactive/Active | Inactive |
| High Beam Select Switch | Exterior Lighting | Inactive/Active | Inactive |
| Incandescent Dimming | Interior Lighting | % | % |
| Instrumentation Backlight | Outputs | On/Off | Off |
| Interior Lamp Output | Outputs | On/Off | Off |
| Interior Light Switch | Inputs | On/Off | Off |
| Interior Lights Power | Outputs | On/Off | Off |
| Interior Lights Power | Inputs | On/Off | Off |
| Learned Home Position | Bass Data | Counts | 0 |
| Learn in Progress | Bass Data | No/Yes | No |
| LED Dimming PWM Command | Interior Lighting | % | % |
| Left Turn Signal Switch | Exterior Lighting | Inactive/Active | Inactive |
| LF Turn Signal | Exterior Lighting | On/Off | Off |
| Low Beam Relay Command | Exterior Lighting | Inactive/Active | Inactive |
| Low Beam Switch | Inputs | On/Off | Off |
| LR Door Open Switch | Inputs | On/Off | Off |
| LR Turn Signal | Exterior Lighting | On/Off | Off |
| Park Brake Switch | Inputs | Applied/Released | Released |
| Park Lamp Relay Command | Exterior Lighting | On/Off | Off |
| Park Lamp Switch | Exterior Lighting | Inactive/Active | Inactive |
| Park Lamp Switch | Inputs | On/Off | Off |
| RF Door Lock Switch | Inputs | On/Off | Off |
| RF Turn Signal | Exterior Lighting | On/Off | Off |
| Right Corner Lamp | Exterior Lighting | Inactive/Active | Inactive |
| Right Turn Signal Switch | Exterior Lighting | On/Off | Off |
| RR Door Open Switch | Inputs | On/Off | Off |
| RR Turn Signal | Outputs | On/Off | Off |
| Stop Lamp Signal | Cruise Control Data | On/Off | Off |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.