Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 165 (ENGINE CONTROLS - 2.2L (L61) INTRODUCTION)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Fastener Tightening Specifications
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2005 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Accelerator Cable Bracket Nuts | 10 N.m | 89 lb. in. |
| Accelerator Pedal Retaining Nuts | 10 N.m | 89 lb. in. |
| Air Cleaner Assembly Attaching Bolt | 10 N.m | 89 lb. in. |
| Air Cleaner Assembly Bracket Bolt | 10 N.m | 89 lb. in. |
| Air Cleaner Intake Duct Assembly Bolt | 10 N.m | 89 lb. in. |
| Air Cleaner Intake Duct Clamp | 5 N.m | 44 lb. in. |
| Air Cleaner Outlet Resonator Clamp | 4 N.m | 36 lb. in. |
| Air Cleaner Outlet Resonator Duct Bolt | 10 N.m | 89 lb. in. |
| CKP Sensor Bolt | 8 N.m | 71 lb. in. |
| Engine Control Module (ECM) Bolts | 8 N.m | 71 lb. in. |
| Engine Coolant Temperature (ECT) Sensor | 10 N.m | 89 lb. in. |
| EVAP Canister Purge Valve Mounting Bracket Nut | 8 N.m | 71 lb. in. |
| EVAP Canister Retaining Bolt | 10 N.m | 89 lb. in. |
| Fuel Filler Hose Clamp | 4.5 N.m | 40 lb. in. |
| Fuel Filler Pipe Attaching Screw | 10 N.m | 89 lb. in. |
| Fuel Filler Pipe Lower Retaining Bolt | 10 N.m | 89 lb. in. |
| Fuel Supply Line Fitting | 10 N.m | 89 lb. in. |
| Fuel Tank Strap Bolts | 25 N.m | 18 lb. ft. |
| Heated Oxygen Sensor (HO2S) 1 | 45 N.m | 33 lb. ft. |
| Heated Oxygen Sensor (HO2S) 2 | 45 N.m | 33 lb. ft. |
| Heated Oxygen Sensor (HO2S) 2 Harness Clip | 4 N.m | 35 lb. in. |
| Idle Air Control (IAC) Valve Screw | 3 N.m | 27 lb. in. |
| Ignition Coil Housing Retaining Bolts | 10 N.m | 89 lb. in. |
| Ignition Control Module (ICM) Screws | 1.5 N.m | 13 lb. in. |
| Knock Sensor (KS) | 25 N.m | 18 lb. ft. |
| Spark Plugs | 20 N.m | 15 lb. ft. |
| Throttle Body Attaching Bolts | 10 N.m | 89 lb. in. |
| Throttle Position (TP) Sensor Mounting Screw | 2 N.m | 18 lb. in. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.