Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROLS - 2.4L - INTRODUCTION (2 OF 2)DIAGNOSTIC INFORMATION AND PROCEDURESDIAGNOSTIC CODE INDEX
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Diagnostic Code Index
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Diagnostic Code Index
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| DTC P0010, P0011, P0013, or P0014 | Camshaft Position (CMP) |
| DTC P0016 | Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation |
| DTC P0017 | Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation |
| DTC P0030, P0036, P0053, P0054, P0135, or P0141 | HO2S Heater |
| DTC P0068 or P0121 | Throttle Body Airflow Performance Throttle Position (TP) Sensor 1 Performance |
| DTC P0101 or P1101 | Mass Air Flow (MAF) Sensor Performance Intake Air Flow System Performance |
| DTC P0102 or P0103 | Mass Air Flow (MAF) Sensor Circuit Low/High Frequency |
| DTC P0106 | Manifold Absolute Pressure (MAP) Sensor Performance |
| DTC P0107 or P0108 | Manifold Absolute Pressure (MAP) Sensor Circuit Low/High Voltage |
| DTC P0112 or P0113 | Intake Air Temperature (IAT) Sensor Circuit Low/High Voltage |
| DTC P0116 | Engine Coolant Temperature (ECT) Sensor Performance |
| DTC P0117 or P0118 | Engine Coolant Temperature (ECT) Sensor Circuit Low/High Voltage |
| DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135 | Throttle Position (TP) Sensor Circuit |
| DTC P0125 or P0128 | Engine Coolant Temperature (ECT) |
| DTC P0131, P0132, P0137, P0138, P2A00, or P2A01 | HO2S Circuit |
| DTC P0133, P0134, P0140, or P1133 | HO2S Circuit |
| DTC P0171 or P0172 | Fuel Trim System Lean/Rich |
| DTC P0201-P0204 | Injector 1-4 Control Circuit |
| DTC P0230 | Fuel Pump Relay Control Circuit |
| DTC P0300 | Engine Misfire Detected |
| DTC P0315 | Crankshaft Position (CKP) System Variation Not Learned |
| DTC P0324, P0325, P0326, P0327, or P0328 | Knock Sensor (KS) |
| DTC P0335 | Crankshaft Position (CKP) Sensor Circuit |
| DTC P0336 | Crankshaft Position (CKP) Sensor Performance |
| DTC P0340, P0341, P0365, or P0366 | CMP Sensor |
| DTC P0351-P0354 |
|
| DTC P0420 | DTC P0420 Catalyst System Low Efficiency |
| DTC P0442 | DTC P0442 Evaporative Emissions (EVAP) System Small Leak Detected |
| DTC P0443 or P0449 |
|
| DTC P0446 | DTC P0446 Evaporative Emission (EVAP) Vent System Performance |
| DTC P0451, P0452, P0453, or P0454 |
|
| DTC P0455 | DTC P0455 Evaporative Emission (EVAP) System Large Leak |
| DTC P0496 | DTC P0496 Evaporative Emission System Flow During Non-Purge |
| DTC P0506 or P0507 |
|
| DTC P0601-P0607, P060E, P062F, P1600, P1621, P1627, P1681, P1683, or P2610 |
|
| DTC P060D | DTC P060D Control Module Accelerator Pedal Position (APP) System Performance |
| DTC P0641 or P0651 |
|
| DTC P0650 | DTC P0650 Malfunction Indicator Lamp (MIL) Control Circuit |
| DTC P0685, P0689, or P0690 |
|
| DTC P0700 or P1700 | DTC P0700 Transmission Control Module (TCM) Requested MIL Illumination |
| DTC P1174 | DTC P1174 Fuel Trim Cylinder Balance |
| DTC P1400 | DTC P1400 Cold Start Emission Reduction Control System |
| DTC P1516, P2101, P2119, or P2176 |
|
| DTC P1682 | DTC P1682 Ignition 1 Switch Circuit 2 |
| DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138 |
|
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.