SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 666 (LIGHTING SYSTEMS)DIAGNOSTIC INFORMATION AND PROCEDURESDTC B2600TEST DESCRIPTION
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2

Test Description

2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Test Description
WARNING: This page is about a different car, the 2006 GMC Sierra, 2006 GMC Cab & Chassis Sierra, 2006 Chevrolet Silverado, and 2006 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the DRL relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  This step tests for voltage at the coil side of the DRL relay.
  3. 4:  This step verifies that the BCM is providing ground to the DRL relay.
  4. 5:  This step tests if ground is constantly being applied to the DRL relay.
  5. 6:  This step tests if there is opposing voltage present or an open in the DRL relay control circuit.
  6. 12:  After replacement of the BCM you must calibrate the new module for proper operation.
DTC B2600

Step Action Yes No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics 
Connector End View Reference: Lighting Systems Connector End Views  or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the DRL relay ON and OFF.
Does the daytime running lights (DRL) relay turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Disconnect the DRL relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the battery positive voltage circuit of the DRL relay and a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4
  1. Connect a test lamp between the control circuit and the battery positive voltage circuit of the DRL relay.
  2. With a scan tool, command the DRL relay ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 8  Go to Step 5 
5 Does the test lamp remain illuminated with each command? Go to Step 7  Go to Step 6 
6 Test the control circuit of the DRL relay for high resistance, an open, or a short to voltage. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7 Test the control circuit of the DRL relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the DRL relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the DRL supply voltage circuit of the DRL relay. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 13  -
11 Replace the DRL relay. Refer to Relay Replacement (Within an Electrical Center) or Relay Replacement (Attached to Wire Harness) in Wiring Systems.
Did you complete the replacement?		 Go to Step 13  -
12 Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.