SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 389 (KEYLESS ENTRY SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESKEYLESS ENTRY SYSTEM INOPERATIVE
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2

Keyless Entry System Inoperative

2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Keyless Entry System Inoperative
WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Keyless Entry System Inoperative

Step Action Yes No
1 Did you perform the Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Remote Keyless Entry 
2 Press each button of the transmitter one at a time.
Does the system operate normally?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 Lock and unlock the door locks using the controls inside the vehicle.
Do the locks operate properly?		 Go to Step 4  Go to Diagnostic System Check - Door Systems in Doors
4
IMPORTANT: Inspect that the keyless entry transmitter is the correct model for the vehicle remote system. A wrong model transmitter may pass this test but will not activate the vehicle remote system.
  1. Turn on the J 43241  Keyless Entry Tester. See Special Tools .
  2. Place the transmitter on the J 43241  test pad.
  3. Press each button of the transmitter one at a time.
Does a tone sound and the green light illuminate on the J 43241  after each button is pressed?		 Go to Step 8  Go to Step 5 
5 Do any of the buttons on the transmitter sound the tone and illuminate the green light when pressed? Go to Step 9  Go to Step 6 
6 Replace the transmitter battery. Refer to Transmitter Battery Replacement .
Did you complete the replacement?		 Go to Step 7  -
7
  1. Turn on the J 43241  Keyless Entry Tester. See Special Tools .
  2. Place the transmitter on the J 43241  test pad.
  3. Press each button of the transmitter one at a time.
Does a tone sound and the green light illuminate on the J 43241  after each button is pressed?		 Go to Step 8  Go to Step 9 
8 Perform the transmitter synchronization procedure. Refer to Transmitter Resynchronization .
 
Did the locks cycle to lock then unlock?		 Go to Step 12  Go to Step 10 
9 Replace the transmitter.
Did you complete the replacement?		 Go to Step 10  -
10 Perform the transmitter programming procedure. Refer to Transmitter Programming .
Did the locks cycle to lock then unlock?		 Go to Step 12  Go to Step 11 
11
IMPORTANT: When replacing the Passenger Door Module (PDM), perform the Program all Transmitters procedure. Refer to Transmitter Programming .
Replace the PDM. Refer to Switch Replacement - Door Lock and Side Window - Passenger in Doors.Did you complete the replacement?		 Go to Step 12  -
12 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 3 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.