Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2133 (LIGHTING SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESCOURTESY LAMPS MALFUNCTIONCIRCUIT/SYSTEM VERIFICATION
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2
Circuit/System Verification
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Circuit/System Verification
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2012 GMC Yukon XL, 2012 GMC Yukon, 2012 Chevrolet Tahoe, 2012 Chevrolet Suburban, and 2012 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
- Ignition ON, observe the scan tool Door Ajar Sw. parameter while opening and closing each vehicle door. The parameter should change between Door Ajar and Door Closed.
- If the parameter does not change between the selected states, refer to Door Ajar Indicator Malfunction .
- Observe the scan tool Rear Closure Ajar Sw. parameter while opening and closing the trunk. The parameter should change between Active and Inactive.
- If the parameter does not change between the selected states, refer to Liftgate Ajar Indicator Malfunction (TB7) , or Liftgate/Liftgate Window Ajar Indicator Malfunction (Manual Liftgate) , Liftgate/Liftgate Window Ajar Indicator Malfunction (Power Liftgate) ,
- Command the Courtesy Lamps ON and OFF with a scan tool. The courtesy lamps should turn ON and OFF when changing between the commanded states.
- If the courtesy lamps do not turn ON and OFF when commanded, refer to Courtesy Lamp Malfunction.
- All doors closed, observe the scan tool Ctsy. Lamp Actv. Reason parameter while turning the dome lamp switch ON and OFF. The reading should change between Off and Manual.
- If the Ctsy. Lamp Actv. Reason parameter does not change between Off and Manual, refer to Dome/Interior Lamp Switch Malfunction.
- All doors closed, observe the scan tool Ctsy. Lamp Actv. Reason parameter while turning the interior lamp defeat switch ON and OFF. The reading should change between Off and Manual Defeat.
- If the Ctsy. Lamp Actv. Reason parameter does not change between Off and Manual, refer to Dome/Interior Lamp Switch Malfunction.
- Turn the individual reading lamps ON and OFF with their respective switches. The reading lamps should turn ON and OFF when changing between the selected states.
- If any reading lamp does not turn ON and OFF when selected, refer to Reading Lamps Malfunction.
- Turn the left and right vanity mirror lamps ON and OFF with their respective switches. The vanity mirror lamps should turn ON and OFF when changing between the selected states.
- If any reading lamp does not turn ON and OFF when selected, refer to Vanity Mirror Lighting Malfunction.
- Command the Courtesy Lamp ON and OFF with a scan tool. Verify the exterior illumination lamps turn ON and OFF.
- If the exterior illumination lamps do not change between ON and OFF, refer to Outside Rearview Mirror Illumination Malfunction.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.