Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2040 (VEHICLE DIAGNOSTIC INFORMATION - SCAN TOOL INFORMATION)SPECIFICATIONSINSTRUMENT CLUSTER SCAN TOOL INFORMATION
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2
Instrument Cluster Scan Tool Information
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Instrument Cluster Scan Tool Information
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Instrument Panel Cluster Scan Tool Data Parameters
| Parameter | System State | Expected Value | Definition |
|---|---|---|---|
| Operating Conditions: Ignition ON | |||
| Battery Voltage | - | Varies | This displays volts. This is the voltage input supplied to the instrument panel cluster. |
| Brake Fluid | - | OK | The scan tool displays OK or Low. This is the state of the brake fluid level. |
| Brake Fluid Switch | - | Varies | This displays volts. This is the voltage status of the brake fluid switch. |
| DIC Fuel Info. | - | Inactive | The scan tool displays Active or Inactive. This is the state of the DIC Fuel Info. switch. |
| DIC Information Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the DIC Information switch. |
| DIC Personalization | - | Off | The scan tool displays Active or Inactive. This is the state of the DIC Personalization switch. |
| Ignition 1 Input | - | Active | The scan tool displays Active or Inactive. This is the state of the Ignition 1 input to the instrument panel cluster. |
| Ignition Cycle Counter | - | Varies | The scan tool displays counts. This is the number of times the ignition has been cycled from the OFF to ON position. |
| Odo/Trip Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the odometer/trip switch. |
| Passenger Seatbelt Indicator Commanded | - | Off | This displays On or Off. This is the commanded state of the passenger seatbelt indicator. |
| Passenger Seatbelt Indicator Status | - | Off | This displays On or Off. This is the state of the passenger seatbelt indicator. |
| Set/Reset Switch | - | Inactive | The scan tool displays Active or Inactive. This is the state of the set/reset switch. |
| Washer Fluid Level | - | OK | The scan tool displays OK or Low. This is the state of the washer fluid level. |
Instrument Panel Cluster Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Dimming | The IPC dims from 0-100 percent when you select INCREASE or DECREASE by 20 percent increments. |
| Display Test | The instrument panel cluster (IPC) illuminates all of the display segments when you select On. |
| Display(s) Test | The instrument panel cluster (IPC) sweeps all gauges when you select On. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.