SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1770 (OBJECT DETECTION SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESREAR VISION CAMERA SYSTEM MALFUNCTION (UVC WITH NAVIGATIONAL RADIO)CIRCUIT/SYSTEM TESTING
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2

Circuit/System Testing

2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Circuit/System Testing
WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

Rearview Camera System Always On

  1. Ignition OFF, disconnect the harness connector X1 at the rearview camera.
  2. Ignition ON, vehicle in PARK, verify a test lamp does not illuminate between the control circuit X1 terminal 3 and ground.
  3. If all circuits test normal, test or replace the rearview camera.

Rearview Camera System Does Not Display

  1. Ignition OFF, disconnect the harness connectors X1 and X2 at the rearview camera.
  2. Test for less than 10 Ξ© between the ground circuit X1 terminal 2 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Engine running, verify a test lamp illuminates between the ignition circuit X2 terminal 4 and ground.
    • If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  4. Park brake applied, transmission in REVERSE, engine running, test for B+ between the B+ circuit X1 terminal 3 and ground.
    • If less than the specified value, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  5. Ignition OFF, disconnect the X4 harness connector at the radio.
  6. Engine running, test for less than 1 V between the following signal circuit terminals at the rearview camera harness connector and ground:
    • Signal (+) circuit X2 terminal 1
    • Signal (-) circuit X1 terminal 1
    • If greater than the specified range, test the signal circuit for a short to voltage.
  7. Test for infinite resistance between the following circuit terminals at the rearview camera harness connector and ground:
    • Signal (+) circuit X2 terminal 1
    • Signal (-) circuit X1 terminal 1
    • If not the specified value, test the circuit for a short to ground.
  8. Test for less than 2 Ξ© between the signal (+) circuit X2 terminal 1 at the rearview camera harness connector and the signal (+) circuit terminal 6 at the radio harness connector
    • If greater than the specified range, test the signal circuit for an open/high resistance.
  9. Test for less than 2 Ξ© between the signal (-) circuit X1 terminal 1 at the rearview camera harness connector and the signal (-) circuit terminal 7 at the radio harness connector.
    • If greater than the specified range, test the signal circuit for an open/high resistance.
  10. If all circuits test normal, test or replace the rearview camera.
  11. Engine running, transmission in REVERSE, verify a clear rear vision image is displayed on the radio.
    • If a clear rear vision image is not displayed, replace the radio.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.